Jump to content
SAU Community

Recommended Posts

To do it properly you'll need to remove the whole roof lining from the car (not just the soft lining, the whole thing), You can do it in the car but may not be as succesful as it keeps trying to droop down while you're trying to stick it back up.

Peel back the section that is coming loose (if you just want to fix that section), spray with contact adhesive (from Bunnings, Supercheap, etc) on BOTH the soft roof lining and the backing panel (not too much that it soaks through), leave until it's tacky both sides then pull the soft lining back over where it needs to go (holding it up over the top, not letting it touch yet) then progressively press the two sections together working towards the outside. It's hard to explain so hopefully that makes sense!

To do it properly you'll need to remove the whole roof lining from the car (not just the soft lining, the whole thing), You can do it in the car but may not be as succesful as it keeps trying to droop down while you're trying to stick it back up.

Peel back the section that is coming loose (if you just want to fix that section), spray with contact adhesive (from Bunnings, Supercheap, etc) on BOTH the soft roof lining and the backing panel (not too much that it soaks through), leave until it's tacky both sides then pull the soft lining back over where it needs to go (holding it up over the top, not letting it touch yet) then progressively press the two sections together working towards the outside. It's hard to explain so hopefully that makes sense!

Dont use contact adhesive it soaks thru and gets clumpy , smells like hell for a while

Use Whorth headliner spray glue from autopaint shop , most others fail in the heat , or 3m super trim adheasive #90

Spotlight sells microfiber suede recover it , much nicer in black suede

To remove lay the seats down and roll down the windows to have room to slide it out easy

Its fragile so becareful

And remove the saggy cloth it you recover it so its smoothe or glue it down first

Edited by Carbon 34

mine is doing this a little too...but its not the liner peeling off the backing. its the whole backing falling off the roof, just replace the old double sided tape that used to hold it up there.

double check that yours isnt the same before you go buying expensive spray glues etc.

mine is doing this a little too...but its not the liner peeling off the backing. its the whole backing falling off the roof, just replace the old double sided tape that used to hold it up there.

double check that yours isnt the same before you go buying expensive spray glues etc.

pretty sure mines like that, i was gonna double sided tape it jsut havent been bothered... might do it befreo it gets worse though

mine is doing this a little too...but its not the liner peeling off the backing. its the whole backing falling off the roof, just replace the old double sided tape that used to hold it up there.

double check that yours isnt the same before you go buying expensive spray glues etc.

Mines doing the exact same thing, any recommendations on double sided tape to use? 3M I assume.

I remember being impressed by 3M as a company after studying a case study about them in uni, so personally I trust them as a company to provide quality products and would choose them among others. Very good R&D

sorry mate not mean to be rude/highjack your topic,where i can buy double sided tape and what brand? mine peeling off too...thanks guys.

Bunnings sells cheap white stuff

Autopaint store sells the 3m green semi strong removable

Or red backed non removable without force or remover soaked rag

Red is what car emblems and side trim is held on with

  • 1 month later...

Most auto stores should sell a spray adhesive for roof linings. Our go to your local hardware shop and buy a can of spray contact adhesive. Will cost less than $20 (i bought some today for a different use). Generally though you will need a new roof lining, because it is the foam becoming brittle that is causing the lining to sag.

Sorry, should have been more specific. The lining is fine, the drooping is where the headliner board (ie the mdf or whatever it is) attaches to the metal roof of the car. There are 3 or 4 contact points at the rear windscreen for this. I need to take another look, but I'm guessing there are Velcro pads or similar that are no longer glued on. New Velcro on loctite 401 could do the trick, spray adhesive sounds more like for the fabric. Just thought there may be a specific hi-temp rated interior glue.

  • 10 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...