Jump to content
SAU Community

Recommended Posts

Who is this ash person.. such a bogan name...I just picture someone with a commo with stockies on it.

And chicken legs :ph34r:

But yeah, Kwaka rules the interwebz

where are you getting this garbage from....throttle bodies are completely closed you goose...until you push the accelerator air is bypassed through your idle control valve and that is what makes it run...when you push the accelerator the throttle body opens and air rushes into the engine cause the revs to rise so the car can move....its simple logic...but in your setup when i push the accelerator according to your "logic" there will only be a small amount of air in the pipe that wont last very long at all and thats assuming you have a leaky throttle body..so i very much doubt its going to last long enough to get the car up to a decent enough speed to create 6psi of boost in the intercooler.. I guesstimate this would take at least 20 mtres of driving...where is your air supply coming form for that 20 mtres?? and its going to take even longer to build up pressure if you have a leaky throttle body....

no throttle body is completely closed, or it would bind/seize with heat...

newer cars with electronic throttle bodies usually don't have iac's

Man I don't know if you guys are taking the shiat out of each other or if use are being serious, but fark this kawasakirider dude is taking the piss out of all of use and use are falling for it by the looks of it, dumb and dumber haha lol.

Man I don't know if you guys are taking the shiat out of each other or if use are being serious, but fark this kawasakirider dude is taking the piss out of all of use and use are falling for it by the looks of it, dumb and dumber haha lol.

Use said it...

  • Like 1

haters be hating.

I'm taking some of these ideas and stepping it up.

have a efi motor to go in my stang as I doubt this would work proper on a carby.

however

going bigger capacity cooler

stiffer spring on TB

using a air -> water intercooler with ice in the reserve tank.

should be kick arse.

haters be hating.

I'm taking some of these ideas and stepping it up.

have a efi motor to go in my stang as I doubt this would work proper on a carby.

however

going bigger capacity cooler

stiffer spring on TB

using a air -> water intercooler with ice in the reserve tank.

should be kick arse.

Build thread?

Long story short.

bought worst car int he world including front wheels 6 inch different mounting.

.got everything fixed, took car in for new starter motor they blew engine and said must have been like it when brought in.

car sat 4-5 years, got drunk at bathurst bought ef falcon for motor

stripped car.

soda blaster coming in this weekend, then new motor paint cruise

oh and Chip foose did a sketch for me

I've received quite a few PM's asking if I could piece together N/A intercooler kits for people.

The answer is no...

1. I don't know what car you have, every car is different (front bar etc) you'll need to mount your stuff so it works, selling a generic kit is bound to generate complaints as I can't be sure it will all fit properly.

2. If you can't plumb an intercooler and a throttle body together, you shouldn't be working on cars. Just enjoy the 100rwkw that your car puts out without my mods.

Sorry to be harsh, but it's that simple.

Edited by kawasakirider

Man I don't know if you guys are taking the shiat out of each other or if use are being serious, but fark this kawasakirider dude is taking the piss out of all of use and use are falling for it by the looks of it, dumb and dumber haha lol.

Nah mang. Use dun even no. Kwaka is straight up yo.

Only Juan?

I just told the whole of the N/A section how to gain ~40rwkw for $200 and still have change for beer.

Juan from me...I only have 1 a day to give out. I think everyone who has an N/A and wants to make 40+ KW should also give you some free internets as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...