Jump to content
SAU Community

Recommended Posts

This morning tried pull ups again..

13

10

9

7

Welcome to the inconsistent world of pull-ups lol. Being body weight, your numbers will fluctuate with what you eat that day :thumbsup:

  • 1 month later...

Awesome thread, can't believe I didn't see it earlier!

I noticed earlier in the thread there were some chin-up numbers thrown in too, so I'll include those as well as my pull-up numbers. With my current training program, I only have 1 working set, which is further broken down in to 3 "rest pause" sets. Google Doggcrapp training for a better explanation. Cliff notes..... You do your first working set. Go to absolute failure, drop down, 10 - 15 deep breaths. Failure again, more deep breaths. Failure again, then you're done.

So.. at a height of about 175cm, and a body weight of 92kg @ around 13%bf...

Pull ups:

15

12

9

Chin ups:

22

17

13

To give a bit of insight... I was doing these same numbers at 85kg (about 2 months ago), so I'm quite happy with my strength progress. Will try 'normal' sets soon, with a bit of time in between each set, instead of my current 15 seconds or so.

Edited by Dajae

Not impossible but very unlikely...more plausible that by 200 in a row he means 200 in succession. Ala what many people I know claim similarly with push-ups, when they really mean sets...

I've seen those videos of those ripped Russian kids who do nothing but pull-ups all day and weigh <60kg, they usually top out below 100. But you do tend to find towards the end that they sit in a dead hang as a rest between reps.

He said they are proper, arm straight full length pull ups. I kept saying are you sure? He said yes. Said he trains 4 to 5 hours a day. 2 hours is boxing specific training the rest is hitt cardio and upper body training he said he does mainly cable work too.

Agreed. Possible, but very unlikely. To have numbers like that would put him into that "elite" bracket. How much does he weigh do you think? Anyone training 4 - 5 hours a day, is either blessed with amazing superb genetics, not training hard enough, or on steroids.

But hey.. tell him to make a video. That'll put a sock in our mouths eh?

Would actually love to see a video of it, not just to prove a point on the internet, but would be pretty amazing just to see it. Talk about a blood pump...

Speaking of pull-ups, in my current state I'm pulling

20

15

10

This is after being sick and taking a month off. So I've lost strength, but have also lost a few kg to balance that out...thus similar numbers to pre-sickness. It's quite a strange feeling actually, the difference in the motion compared across two different body weights.

Indeed! It would be quite the accomplishment... Especially if he actually weighs a fair bit. I mean, rock climbers that weigh <60kgs have no issue doing 30 - 50, but a big boxer doing 200? Damn.

Nice numbers man! With the pronated grip, I like going wide to hit more upper back and rhomboid action.. As a result, my elbows tend to get a little sore.

Do you get the same as this? Or are your pull ups done with only a slightly wider than shoulder width grip? If I bring my pronated grip in somewhat, I can manage a few more reps (18), but I feel it less in the upper back, and more in my forearms.

Anyone here like neutral grip pull ups? I find these to be the best of both worlds.

My pull-ups are neutral grip. I used to do wide pronated, but after (a likely unrelated) shoulder injury, I started back on pull-ups with a neutral grip for less strain on the injury. Can probably do a couple more reps this way than wide, but it does still feel like a complete motion. I feel like you can get a slight rowing benefit too, without kipping the legs up, as you can easily change the angle of your body using longitudinal hand grip (if you have the strength) and leg position to hold that angle in place. It definitely hits the abs/core hard.

Between those and deadlifts I don't feel the need to do much else, except maybe something for rear delts.

Ah ok, nice work. You're definitely right in regards to shoulder friendly benefits.. much kinder than wide pronated.

For all my pull ups/chins, I keep my legs out straight in front of me, at an angle. I find it helps keep more tightness throughout the motion, and yes, very good stimulus in the core region.

I wish I could just get away with deads and squats for "frontal core" strength.... eg abs... However my physio advised me to include some form of weighted 'crunch' movement (back friendly variety) as my lower back tends to be much stronger than the opposite muscles..

Face pulls are great for rear delts and shoulder health. Ever had much experience doing them?

In terms of that crunch movement, assuming I know what you're talking about, three recommendations for exercises I've enjoyed on the front side:

1. Captains chair leg raises, as many of these "machines" keep the lower back static with pads and, provided you have no hip issues, shouldn't give you any injuries beyond a stretched hamstring from raising too high. I usually do it after deadlifts to finish off abs, but coincidentally it's a good stretch for the hamstrings after getting them tightened on deads.

2. I have a nautilus type crunch machine that is basically a seated crunch. You can keep adding weight to it and I felt my abdominal wall develop some real thickness to it using this. Didn't take me long to max out the weight stack for 20 reps but the problem is that, like all machines, if your body isn't proportionate to it (even though it's adjustable), you can cause yourself some damage at high weights because of the rigid motion...which sounds more ironic than it is. My lower back got a bit twitchy after prolonged use of this one, though maybe I was too focused on doing more weight and lost my technique in trying to leverage it.

3. Kneeling crunches on the tricep pushdown (for lack of the proper term for this exercise), where you kneel on the ground, hold a pushdown rope behind your head and do crunches towards the ground.

I've given face pulls a go and they felt very awkward and it did mess with the joints a bit - could have been a bad angle. I must try again since my shoulder has advanced a bit. It would probably help to have someone watch and advise if I'm doing them properly, too, as all well and good to think you are doing it but it can look very different!

In terms of that crunch movement, assuming I know what you're talking about, three recommendations for exercises I've enjoyed on the front side:

1. Captains chair leg raises, as many of these "machines" keep the lower back static with pads and, provided you have no hip issues, shouldn't give you any injuries beyond a stretched hamstring from raising too high. I usually do it after deadlifts to finish off abs, but coincidentally it's a good stretch for the hamstrings after getting them tightened on deads.

2. I have a nautilus type crunch machine that is basically a seated crunch. You can keep adding weight to it and I felt my abdominal wall develop some real thickness to it using this. Didn't take me long to max out the weight stack for 20 reps but the problem is that, like all machines, if your body isn't proportionate to it (even though it's adjustable), you can cause yourself some damage at high weights because of the rigid motion...which sounds more ironic than it is. My lower back got a bit twitchy after prolonged use of this one, though maybe I was too focused on doing more weight and lost my technique in trying to leverage it.

3. Kneeling crunches on the tricep pushdown (for lack of the proper term for this exercise), where you kneel on the ground, hold a pushdown rope behind your head and do crunches towards the ground.

I've given face pulls a go and they felt very awkward and it did mess with the joints a bit - could have been a bad angle. I must try again since my shoulder has advanced a bit. It would probably help to have someone watch and advise if I'm doing them properly, too, as all well and good to think you are doing it but it can look very different!

For the leg raises, I could never seem to feel it adequately enough in my abdominal muscles.. My hips always felt like they were doing more of the work. I tried a variation where I would hold a light dumbbell between my ankles, and with a bend at my knees, I would raise my upper legs up, and then try to "tuck up" my pelvis to my chest.. Seemed to work a little better for me.. However when a few friends tried, it had the opposite effect! Strange how everyone reacts so differently at times.

Yeah nice.. I have something similar, a weight plate loaded hammer strength crunch machine. Really like this machine.. The machines upper and lower portions are required to move, rather than just the upper/lower without the other. Definitely noticed some more "popping out" action with these!

Ahhh yes.. I love cable crunches. Such a good exercise if the form is good, ie, no swinging motion. The fact that it can be weight resisted is also a big win for me. I always believed that if you're training the rest of your body against a resistance (usually increasing weight), then the same should be done for the core. Planks with a 20kg plate resting on my glutes is also good for some isometric strength.

Face pulls can be tricky that's for sure! Found out I was doing them wrong for quite some time. Here is a video I found which helped me...


(couldn't get the linking feature thing to work :/ but if you go on youtube and search "face pull technique", the video by scott herman fitness is the one )

I'll watch you

:ninja:

Lol'd so hard. That emoticon is so good.

Edited by Dajae
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...