Jump to content
SAU Community

Reducing Weight Of M35 Stagea's

matt13b

By matt13b,
in Four Door Family & Wagoneers

 Share

Recommended Posts

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

andy65b Veteran

andy65b

Posted
Posted

Not sure your weight figure is correct.

An ARX is 1780kg and an RX is 1680kg.

But if you want to lighten it have a look at changing Electric front seats or removing some of the electronics.

There are not many other places to loose weight as the subframe and suspension are all alloy, bonnet is alloy, boot is plastic composite.

On the upside, all that weight is near perfectly balanced on the chasis with 52% on the front axle and 48% on the rear.

Enjoy.

Daleo Grand Master

Daleo

Posted
Posted

Nope, RX is awd, as is the RS.

Mine weighed in at 1670kg on the weighbridge at my work.

Considering a stock VE sedan is 1700kg, and even a fully loaded FPV ute is over 1800kg; I don't think there's much to worry about.

I know what I'd rather be driving in an accident.

Or any other time for that matter...

PN-Mad Grand Master

PN-Mad

Posted
Posted

RS if you have triple gauges in the centre, RX if you don't. I think that is a safe measure, unless installed later, right guys?

Or plug in your VIN into something like epc data for the run down.

Commsman Veteran

Commsman

Posted
Posted

180sx: 1150kg and three times as powerful as your car.

You Jelly?

^ Yes, yes I am.

I put mine (RS) on the local weighbridge & it came in at 1800kg with me in it, after I had removed all the ususal suspects (spare wheel, tools, sub, mats etc.). All the lux adds weight, no doubt.

I'm not concerned though. This article on the weight of the R35 GTR gives me some peace. http://www.topgear.com/uk/photos/kazutoshi-mizuno-nissan-gtr-interview-top-gear-2012-02-23?imageNo=1

With the right tyres, our cars handle better in torrential rain than most do in the dry.

joshm35 Veteran

joshm35

Posted
Posted

Your in a wagon who cares for weight loss. Rip out your high flow vq and send it to me. That should save you a good 300 kg, take off your wheels and stick it up on blocks that will save you 100kg give or take. Take out your r35 gtr seats, bc's and swaybars and that should save another 50kg .So that will make you about 250 kg heavier than the 180 but you wont be moving far....

Daleo Grand Master

Daleo

Posted
Posted (edited)

I care for weight loss funny man. That's why I started the thread.

But all you're going to end up with is a noisier, harsher, less pleasant car to drive.

And it might accelerate a poofteenth quicker, or save a bees dick of fuel?

If weight saving was your primary concern; why on earth did you buy a Stagea?

If you do anything to your car that displeases me; I may have to kill you.

Lol, jokes. :whistling:

But seriously; don't. ;)

Edited by Daleo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...