Jump to content
SAU Community

Recommended Posts

Breathing all good?

yea catch can v4 has done the trip

have not had to deploy the scaveng pump just yet

thats pretty good considering 12x12 minute sessions half at 15psi and half at 19psi

Did you throw in a fuel cooler??

yea i did in the end

fuelcooler_zps1b8723f9.jpg

on the 12 session i had the tank at 1/4 and did a session after 4 laps the secondary pump got noise and the ecu went into linp mode ( fuel pressure protection) so we know that works

restatr car with fuel and all fixed

  • 1 month later...

minor update

been working on these fckers for a while

i want more stopping power

so 996/7 porka cup calipers

380mm full floating rotors(off getting machined)

new brake line, new pads

custom hub adapters and billet dog bones

i was very happy they fit under the 18's

just buy about 7 mm

GRC_0223_zps639581dc.jpg

GRC_0224_zpse503c658.jpg

  • 2 weeks later...

rally sprint done and dusted

tops fun you guys should get out there

i almost died about 10 times

fastest time got me 10 out of 80

and more importantly beat the only other r33 gtr out there by 9 seconds( although he won a trophy for our class, should have checked they had me in the right class to begin with...lol)

my first ever youtube video check it... after it uploads

http://youtu.be/joAU_gEKMdA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...