Jump to content
SAU Community

  

55 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

As all young guys who buy a skyline they try their chance in getting approved to drive their turbo skyline coupes for no other than hoon purposes, even if some may have LEGIT reasons they are mixed with the feelings of wanting to be behind a wheel of some power. I am no different.

I will be sending off my exemption form to VicRoads, as my circumstances (this is actually legit, believe it or not lol) are that I have MAJOR educational travelling issues.

I live in Meadow Heights, next to Broadmeadows, im sure most people from Victoria know. I go to La Trobe University Bundoora. Thus if I go by car It takes me about 40 minutes to drive there with little to none traffic, also depending on my route. Driving through barry road then Sydney road then freeway then plenty road then my University. Point is its fregging long and by transport, its much, much worse. pretty much impossible by public transport.

need to take bus at Broadmeadows then go all the way down then walk take a tram then walk to my uni, this takes about 1.5 hours of my time. that's 3 hours a day and I go 5 times a week about 3 hours a day so for 3 hours a day im going to be losing another 3 hours of my life.

mind you this is all legit, and so is the want to drive this turbo'd car, not going to lie.

fact is I have no other car to drive with. and NO SHIT I could've bought another car but believe it or not I got this pretty dam cheap and runs smooth, so hell why not take a shot.

Anyway told you the scenario. What are my chances, put a poll up.

Link to comment
https://www.sau.com.au/forums/topic/423438-will-i-get-my-exemption-approved/
Share on other sites

As all young guys who buy a skyline they try their chance in getting approved to drive their turbo skyline coupes for no other than hoon purposes

Wrong. I didn't, because I knew the rules and accepted them. I didn't have the arrogance to think I could loophole through the system. I'm usually a P-plate sympathiser, but you didn't start this post on a good note.

You're probably not going to get an exemption since you knowingly bought a car that you full well knew you are prohibited to drive, and you had equal opportunity to buy a car that's p plate legal. They're not going to accept "oh it was a good buy, so i bought it, now i've already got it..."

Edited by alex182

It may have been cheap but the running costs (fuel) is going to end up costing you much more than if you'd bought a cheap 4 cylinder. You have to run it on premium and your economy will be poor compared to a natro 4 cylinder. I hope you thought about all this, and the day to day practicalities if owning a turbo car when you are a uni student (who generally don't have much money).

And as Alex said, there are plenty of people who respect the law and don't act like a spoilt brat (not a dig at you personally, but all platers who buy a turbo car then try for an exemption).

No, you will get declined. I myself have a high powered vehicle exemption. But it is for work purposes, not just because i want to drive a turbo on my P's. I originally got knocked back on the application because i didn't provide enough information, a quick re-submit and a phone call to the lady that actually reveiws the applications and i was all set. I can drive whatever the hell i want between 6:30am and 6pm :)

But i still need to use P plates, which is annoying because i'm always in and out of different cars but i can live with it.

Sell the skyline and buy a cheap Fiesta or something until you can legally drive it.. i'm telling you now, you won't get approved.

1 As all young guys who buy a skyline they try their chance in getting approved to drive their turbo skyline coupes for no other than hoon purposes, even if some may have LEGIT reasons they are mixed with the feelings of wanting to be behind a wheel of some power. I am no different.

I will be sending off my exemption form to VicRoads, as my circumstances (this is actually legit, believe it or not lol) are that I have 2 MAJOR educational travelling issues.

I live in Meadow Heights, next to Broadmeadows, im sure most people from Victoria know. I go to La Trobe University Bundoora. Thus if I go by car It takes me about 3 40 minutes to drive there with little to none traffic, also depending on my route. Driving through barry road then Sydney road then freeway then plenty road then my University. Point is its fregging long and by transport, its much, much worse. pretty much impossible by public transport.

need to take bus at Broadmeadows then go all the way down then walk take a tram then walk to my uni, this takes about 1.5 hours of my time. that's 3 hours a day and I go 5 times a week about 3 hours a day so for 3 hours a day im going to be losing another 3 hours of my life.

4 mind you this is all legit, and so is the want to drive this turbo'd car, not going to lie.

fact is I have no other car to drive with. and 5 NO SHIT I could've bought another car but believe it or not I got this pretty dam cheap and runs smooth, so hell why not take a shot.

Anyway told you the scenario. What are my chances, put a poll up.

1 - No, not all young guys will, but people who wants to write off their car within 12 hours and selling it to me to wreck, will try (this has happened). I bought my NA R34 and it runs fine and I'm happy with it as a daily (very awesome daily as a matter of fact).

2 - No form of transport requires a turbo. Exemptions are granted if your vehicle is a turbo DIESEL or it is a utility vehicle such as a ute or other heavy workhorses, thus you would need to demonstrate or prove that it is necessary for the course of your employment.

3 - 40 minutes or not, does not require you to drive a turbo vehicle. Using this as an excuse will only let them think that you'd be speeding with your turbo car and hence get declined.

4 - Not really legitimate reasons for exemption.

5 - Then you should have bought another car.

There are two words that come into mind in this thread, they are "want" and "need". You basically NEED a metal box with 4 wheels that can take you from A-B. You WANT a turbocharged fast metal box with 4 wheels, to take you from A-B.

However this is coming from Nanny NSW. Might be less tougher in VIC.

I personally think that your chances at getting an exemption is next to 000.0001%. Though if you do get approved then I'll personally fly down there and buy you a beer :cheers:

I'm due to apply for one over the coming months, though I have a legitimate reason as I now work in the automotive industry.

What type of car is it? I just got mine for a r33 gtt. I dyno'd and weighed it and got approved no worries.

Not to sure on Vic rules but if your car is 125 at the wheels or less than it is at the legal max at the fly. If it is look into it and apply

On another note. They are REALLY!!! REALLYYYY thirsty.

I can see your reason but I agree with the 4 cly n/a thing, I'm considering going back to my ford focus and driving the skyline on weekend so I can wait till I get a pay Rise to pay for fuel.

Edited by cowdy

When I was attending Uni it took me 2 hours by public transport there and back. That's 4 hours a day, 5 days a week. Did this for about 1 and a half years.

I did not ask for an exemption. Instead I worked hard, saved my money and bought a P-Plate legal car.

No offence but I do think you went about this the wrong way but either way good luck to ya!

When I was attending Uni it took me 2 hours by public transport there and back. That's 4 hours a day, 5 days a week. Did this for about 1 and a half years.

I did not ask for an exemption. Instead I worked hard, saved my money and bought a P-Plate legal car.

No offence but I do think you went about this the wrong way but either way good luck to ya!

exactly. i did that through uni (for 3 years mind you) AND now working at the same uni, it is my daily commute (insert face palm). suck it up OP...

If it takes 40 mins by car from Broady to Bundoora then you are doing it wrong.

The point remains - you didn't need to purchase a illegal car, so why should you be exempt? If I was the person responsible for reviewing your app, you'd be denied

  • Like 1
  • 10 months later...

Sorry to bring up an old thread but I just got done last night by highway patrol driving my stagea do I'm going to try for an exemption again. Is there any way to get a tuning shop to do a low power dyno run so the car still comes up under powered? I have a fmic, 3" turbo back, hypergear op6 highflow and 255lph walbro pump. Do they inspect the car for mods or can you just hand them a dyno sheet and the results from weighing the car?

I doubt you'll get one, and there are plenty of wagons you could've bought that are not on the banned list; so I doubt that will fly as a reason.

They will have a listing with the factory power for the engine, and will use that rather than a deflated dyno figure you are clearly using to try & get around the rule; everyone know's you're going to bump the power straight back up anyway; right?

Sometimes it's better to wait until you don't have to break the law, and drive the car you are allowed to drive.

Why do P platers insist on buying cars they cannot legally drive? I dun get it.... Go out and buy a VL like 90% of them, do some skids. When you can legally drive a real car buy it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...