Jump to content
SAU Community

Recommended Posts

Hello,

this is my rb26/30 build

by kanaris engine in melb

rb30 block - cryogenic block and girdle

cp pistons

9310 pins

upgraded loxx by cp

carrillos rods

AT1 balancer

L19 Head studs

Jun 12 main studs

9L sump ASR

Billet motorsports external oil pump kit

annual groove main tunnel

Head getting done now

2mm inlet/2mm ex valves

supertech valve springs seats retainers

ferrea valve locks

tomie 260/270 cams 10.25 lift

tomei lifters

tomie cam gears

looking at 1000hp at the engine

going in vl

post-87775-0-67934300-1366281902_thumb.jpg

post-87775-0-07005600-1366281915_thumb.jpg

post-87775-0-07661800-1366281926_thumb.jpg

post-87775-0-42773000-1366281938_thumb.jpg

post-87775-0-10906700-1366281950_thumb.jpg

post-87775-0-54303800-1366281964_thumb.jpg

post-87775-0-53420400-1366281976_thumb.jpg

post-87775-0-68541000-1366281985_thumb.jpg

post-87775-0-61220500-1366281996_thumb.jpg

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/423779-rb-2630-build/
Share on other sites

I always thought running flat tops means u can run more lift.

comp ratio going to be around 7.8 to 8.1

reason that low comp - less pinging high boost ,

makes more power then high comp - all types of fuel

I notice a lot of high comp boost rb have head/studs lifting issues

allways prefer low comp high boost/ high comp low boost

Link to comment
https://www.sau.com.au/forums/topic/423779-rb-2630-build/#findComment-6823429
Share on other sites

  • 1 month later...
  • 3 weeks later...

I here'd about weathering/seasoned blocks are better for hp than new block for cast iron - new block will move and flex up until 100,000km

Idea is the hot and cold temp stop the cast iron from expanding/ flexing - taxi blocks would be good idea

I left the rb30 block outs side for 6 months bare wit the girdle and just befor sent to engine shop I went to cryogenics

I believe this theory works , some might disagree

crank wouldn't think be any benefits

only cost $200 shop in melb -http://www.cryocycle.com.au/

Gerry

Edited by chairman
Link to comment
https://www.sau.com.au/forums/topic/423779-rb-2630-build/#findComment-6922218
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...