Jump to content
SAU Community

Recommended Posts

Hypergear billet T67

highmount mani (NZ one or better)

External gate w/ screamer

Bosch 1000cc injectors

Adaptronic ECU from hypergear
Brass button clutch

4" exhaust

GTR FMIC or better

Tune on E85
Mickey Thompson ET Streets
Slick driving with little to no mechanical sympathy.

Link to comment
https://www.sau.com.au/forums/topic/425210-10-second-rb25/#findComment-6850213
Share on other sites

Strip as much weight as possible. and loss 20kgs.

Do all the necesensary engine mods

Run our Billet T04Z with proper manifold and 60mm gate to about 500rwkws

Cutch

re-enforce drift shaft and stronger diff

With bit of luck that the stock gear box won't blow to piece Or put a dog box auto in there.

get adaptronic or some thing similar to setup launch control.

Cross ply M/T wheels and rims

Learn how to drive

By Then you can probably on a flat 10s

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/425210-10-second-rb25/#findComment-6850237
Share on other sites

Strip as much weight as possible. and loss 20kgs.

Do all the necesensary engine mods

Run our Billet T04Z with proper manifold and 60mm gate to about 500rwkws

Cutch

re-enforce drift shaft and stronger diff

With bit of luck that the stock gear box won't blow to piece Or put a dog box auto in there.

get adaptronic or some thing similar to setup launch control.

Cross ply M/T wheels and rims

Learn how to drive

By Then you can probably on a flat 10s

so roughly

3k ish for turbo,gate and ecu if all bought from you...?

1.5k for manifolds and bigger TB ....probably second hand...

1.5k for fuel system, 2000 cc injectors pump, surge tank rail and reg..

1.5 for big Clutch

1.5k for tuning and bits and pieces

I'm up to 9k still need a diff /tailshaft or tyres...but budget is looking like it could be acheivable

blow and hookers aren't looking good but pretty sure all the girls will get wet when I win this race anyway :D...

guys this is a piss take.

you could of had a 10second car man...instead you bought a clubsport :P

Link to comment
https://www.sau.com.au/forums/topic/425210-10-second-rb25/#findComment-6850495
Share on other sites

so roughly

3k ish for turbo,gate and ecu if all bought from you...?

1.5k for manifolds and bigger TB ....probably second hand...

1.5k for fuel system, 2000 cc injectors pump, surge tank rail and reg..

1.5 for big Clutch

1.5k for tuning and bits and pieces

I'm up to 9k still need a diff /tailshaft or tyres...but budget is looking like it could be acheivable

blow and hookers aren't looking good but pretty sure all the girls will get wet when I win this race anyway :D...

you could of had a 10second car man...instead you bought a clubsport :P

i dont need to run tens.

the only 10 i need is in my pants.

Link to comment
https://www.sau.com.au/forums/topic/425210-10-second-rb25/#findComment-6850514
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...