Jump to content
SAU Community

Circuit Racing Thread

Snowman
 Share

Recommended Posts

  • Replies 90
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Snowman
Snowman

PIARC weekend was fun. Next time out we'll be racing together at the Winton 300 rather than against each other.

femno
femno

Yep, me. Been running since the start of the season and ive never had more fun in a car! (The GTR is a different beast, I still love it). It is a serious amount of fun with grids as large as 23 (I t

PN-Mad
PN-Mad

Correct.Only standard rebuild tolerance is accepted. You can bore 0.6mm out the block. You can take 0.25mm off the head. But the compression has to be with a specified range. It's all in the regs.

Posted Images

Snowman Grand Master

Snowman

Posted
  • Author
Posted

Will try and post up some vids later. The "win" vid is pretty unexciting if I'm honest.

However the rest of my weekend sure was a lot more interesting in a way than my first day.

Sunday morning we had our full audit scrutiny done - of which part was to test the kill switch. What I didn't know is that a kill switch cut-off in my car sends the car into limp mode.

This was only discovered as I headed out onto the track to take my position on pole for race 2. Unfortunately it meant I had to head into the pits and had a DNS for race 2. The fix for the limp mode is a simple plug into a PC and clear the fault so I was fixed 5 mins later but it was a simple lesson learnt on my first race weekend.

Upshot of this was it meant for the final race I started from the back of the grid. Conditions on Sunday were dry so the top GT cars had more speed on me regardless but none the less I was able to make my way from 20th all the way back up to 5th by the end of the 12 lap race. In reality I probably would have ended up in 5th even if I started 5th as the top cars are a good few secs / lap quicker than me at this stage.

But it was great fun coming through the field and was a nice learning experience including some pretty fun passes such as going between 2 cars down the main straight with only a few cm's space on each side.

Was good fun and I look forwards to the next one in Oct.

736730_10151775734707387_646209830_o.jpg

Snowman Grand Master

Snowman

Posted
  • Author
Posted

Here's the race win vid. Other than trying to go from hero to zero at turn 2 and dealing with lapped traffic at the end (yep I had lapped traffic in a 4 lap race) it's not all that exciting.

Still - here it is.

  • Like 1
  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • jez NF
      The Evolution Of "night Fury"

      By jez NF · Posted

      75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...