Jump to content
SAU Community

98 Plus Octane Booster

MRHD66

By MRHD66,
in Engines & Forced Induction

 Share

Recommended Posts

Joshbigt62r Proficient

Joshbigt62r

Posted
Posted

You can get e85 delivered in drums but it's quite expensive isn't it compared to at the pump.? Better off going water methanol + 95-98 octane fuel preferably 98 octane and water/meth as jet_r31 mentioned.

Cheers Josh

XR Pilot Contributor

XR Pilot

Posted
Posted (edited)

I looked into this a fair few years ago before E85 was available - octane booster will generally raise a fuels given octane by a few points. Ie point-something of an octane. So 98 will become 98.2 octane for example. The only way to get a decent boost in octane is to mix something like Toluene with 98 (121RON, turbo F1 cars used an 86% Toluene/14% n-Heptane filler blend. It's pretty nasty to handle but you could get it in drums as of a few years ago). Mixed at 65% 98 / 35% Toluene this will get you up to around the same octane as E85 at a much higher cost vs pump E85.

I think your only viable options are either reduce the compression ratio of that motor to run 98, run water/meth like Darren said (if you do run water/meth I'd listen to this man!), buy E85 drums or take a trip to either Newcastle or Kempsey and fill up a few jerry cans.

Edited by XR Pilot
WMDC35 Experienced

WMDC35

Posted
Posted

Octane booster is also completely unreliable and probably doesn't even add half as much octane rating as claimed. I made some from mothballs and petrol in the 1990s that was probably at least as effective (ie it didn't really do anything).

mythbusters did a test with fuel additives, the moth balls seemed to do pretty well haha

JustinP Mentor

JustinP

Posted
Posted

I definitely would not recommend using 98 + octane booster. Due to some flooding that we had a few years ago, I got stranded in my R34 and was forced to use 91 RON fuel as it was the only option I had to get home. I added octane booster as a safeguard. Still suffered engine failure haha :P Thankfully I can laugh about it now! 3 years and counting and I still have not finished rebuilding it!

I would recommend the water / methanol option. But remember, as you are relying on it for everyday driving you need to make sure the setup is ultra reliable and has the appropriate failsafes.

Super Drager Mentor

Super Drager

Posted
Posted (edited)

I definitely would not recommend using 98 + octane booster. Due to some flooding that we had a few years ago, I got stranded in my R34 and was forced to use 91 RON fuel as it was the only option I had to get home. I added octane booster as a safeguard. Still suffered engine failure haha :P Thankfully I can laugh about it now! 3 years and counting and I still have not finished rebuilding it!

I would recommend the water / methanol option. But remember, as you are relying on it for everyday driving you need to make sure the setup is ultra reliable and has the appropriate failsafes.

Well that sounds wrong, if you weren't on boost and loading the car up it shouldn't matter. Baby the car and you can drive it on 91 octane easily. I've never seen a car so aggressively tuned on the low load part of the map that it detonates on 91 octane.

Edited by Super Drager

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...