Jump to content
SAU Community

Auto Swing Mirrors?

NeilC

By NeilC,
in Car Audio & Electrical

 Share

Recommended Posts

NeilC Contributor

NeilC

Posted
Posted

Am in the process of removing a cheap crappy alarm fitted to my R34 4 door and replacing it with a better one. Found the trigger points for the passenger doors ok and figured out how to trigger drivers door. On removing drivers door trim to check wiring i found this box wired into the mirror switch. From some research I believe it to be the module for the auto swing away mirrors. It had been disconnected but I would love to see if I could reinstate it. One side goes to the mirror switch and is plug and play. The other three wires however have me guessing. I split the box and they are marked on the circuit board as follows.

B+ (Straight 12v or Acc/On ?)

Earth (Obvious)

Sig (Trigger wire possibly?)

Its the signal wire that has me stumped. Am presuming that it was connected to the dealer/factory remote central locking to which I didnt get a remote for and was activated when you locked the doors either by key or remote. Anyone got any ideas?

post-114090-0-76317500-1372379106_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/427730-auto-swing-mirrors/
Share on other sites
NeilC Contributor

NeilC

Posted
  • Author
Posted

Sorted. Thanks Chris. you were right in that they take their power and signal from the keyless entry module. Power from pin three and signal from pin six. At first there was nothing. Had the switch on the door in the neutral position thinking that the module overrode the switch function. Wrong it has to be switched to the out position to work. A bit of buggerising around but is now working. Hit the lock key on my remote and the mirrors swing in. Turn the ignition on and they swing out. Cool little feature with no real use here except for the novelty factor I guess.

darksky34 Mentor

darksky34

Posted
Posted

Hand for tight street parking. Or in my case Redcliffe street parking where the idiots get within 2" of your car and destroy mirror housings.

yes. i once got back to my car with the driver side mirror facing outwards.....i was very pissed off but the person/car that did it was no longer there.

Got a Pulsar Grand Master

Got a Pulsar

Posted
Posted

Where can I get one of these little modules? I would love for my mirrors to swing in and out automatically.

Tommy_J <<<--------- This fella had some, I bought one from him but haven't installed it yet...

MrRx7s3 Mentor

MrRx7s3

Posted
Posted

Mine is a factory nissan accessory item. Read on another post that someone used a jaycar module for auto window rollup to do the same thing.

Hey man I've just been searching the forum to find it but I can't find it anywhere, would you be able to direct me in the right direction please, thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 Autech 260RS Wiring Diagrams

      By Duncan · Posted

      Agreed, I've never seen a 260RS specific manual. As GTSBoy said it will mostly be stagea other than the engine loom https://www.hgeconsulting.com.au/stageaservicemanual.pdf
    • GTSBoy
      S1 Autech 260RS Wiring Diagrams

      By GTSBoy · Posted

      You'lll likely have to make do with R33 GTR for engine/tranny stuff, and Stagea for the body. I don't know that there's even been an actual diagram seen in the wild.
    • Marek
      Hi everyone.

      By Marek · Posted

      Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • DanMac34
      R34 Speedo not working after manual swap

      By DanMac34 · Posted

      Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
×
×
  • Create New...