Jump to content
SAU Community

Recommended Posts

I would say, on the basis that the tests you have done so far are likely to give the highest possible fuel pressure you will ever see (cold weather, cold fuel, brand new pump) that you could get away with setting it just barely higher than it runs naturally. So maybe 63 or 64 psi. I would say that you are dead unlikely to get any more than you already are, and even if you did it would only be 1 or 2 psi, which would hardly ruin anything for you (richer is safer anyway).

As long as the reg and the fuel pump can keep that pressure stable across your whole operating range you should be gold.

As to your question about whether the loop you have in your line is causing any restriction....I would suggest not. Unless the hose is quite severely closed down it will still not have anywhere near as much restriction as the reg itself.

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

.... wait for it.

My bet is that you have an air bubble between the fuel an gauge. Due to the orientation of your gauge.

Cheers

Justin

Which has only manifested itself as an issue now, after installing a bigger fuel pump? After running without issue for over a year on the old pump setup?

Air is more compressable then fluid, and would make the gauge read lower if anything. So that is not the problem

So restriction or FPR issue I say. I would pull the FPR off and just have a look at the ports and everything just in case theres something silly going on there

Might have found the issue! Pulled the regulator off last night and had a look at it, but couldn't see anything out of the ordinary. So then I had a look at the piece of return line that came off the regulator and looped around the fuel filter and spotted this:

431226_10151483541942541_708608272_n.jpg

There's some sort of restrictor in there. Makes me wonder where this hose came from, I never purchased any hose with a restrictor in it. In fact from memory I actually just reused the standard return line, though surely they don't have a restrictor in there? Amazes me that it didn't cause any problems until now. Anyway, haven't had a chance to check whether I can lower the fuel pressure now, will finish installing the ethanol sensor and put it all back together and report back!

Yeh, me too... Wondering if maybe this caused some of my power issues, but I don't think so. Tuners never mentioned fuel was a problem, and it wouldn't have affected response anyway. In any case, I'm sure it wasn't doing any good, so I'm glad to be rid of it!

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...