Jump to content
SAU Community

Recommended Posts

u might wana read over the 11 pages again :P

not sure what the big issuel is.... cut the black wire... connect it to a bolt so its grounded...

put foot on accelerator... watch us gauge shows 7psi before you get to 4500rpm.....

I guess it wont work in *everyones* car but from what i've read in the last 11 pages.. looks like its worked on 90% of them...

Would it still work if you splice into the wire like a T.. or do you actually have to cut it ?

try hook it upto a differant bolt ??

I dont know squat about electronics etc, but when i was trying to ground something else on the bolts near the gearstick inside the car, i found a few of them didnt work as a ground very well..

another thing to test.. try disconect the black wire completly and just make sure the boost never goes over 5psi.. (evan at over 4500rpm)

justin i'm not saying it is hard to do. Shit it's only a 2 min job all i'm saying is i can't notice any difference

It works fine for me and I notice quite a difference. Try this. Get on a Freeway in 3rd gear. Get it on full boost at 3000RPM, then flick the switch. Sounds Crazy!!!

Is it possible for this to work if you just bypass the control valve all together.

EG.

It has one pipe going in and one out. If you just take them both off and join together. Wouldnt that to the same affect????

Guys this trick really does work, it makes a hell of a difference.

Just look at the Dyno sheets i was given after my mechanic did it.

It was on the dyno as he was tuning my SAFC but he noticed this mod hadnt been made so he took the liberty of doing it with dyno curves before and after.

Red line is before SAFC (Ignore)

Green line is after SAFC tune

Blue line is after boost controller mod

Gain of 200NM of torque, a shift in the power curve to the left, and boost comes on heaps earlier.

JUST DO IT!

post-23179-1143511011.jpg

post-23179-1143511038.jpg

post-23179-1143511060.jpg

There is another way to do this with exactly the same results. The only difference being that it is not visable inside the engine bay, or if wanting to use a switch can be done from inside the cabin. ( no running wires through the firewall)

Items required

wire ( different colors prefered)

Spade conectors

12 v 30amp changeover relay

on/off switch

Tools required

- wire cutters

- wire crimpers

Time taken about 30 min

This involves cutting wores directly from the ecu located in the passenger kickpanle. if you are not able to, or are not sure of which wire to cut, DONT do this!

1 - Remove passenger kickpanel

2 - on ECU locate plug second from bottom ( while it is still mounted in car)

3 - locate light green wire coming from this plug.

4 - cut wire

5 - install relay

Wiring for relay is:

30 - to green wire car side

87a - to green wire ECU side

87 - to pin 86 on this relay

85 - accessory 12v

86 - switch

6 - install switch

Wiring for on/off switch

pin 1 - to pin 86 of relay

pin 2 - earth

7 - reassemble car

8 - test drive

When the switch is in th ON position you will have high boost mode all the time, when the switch is off, it will run as a standard car ( hi/low boost mode)

Notes:

- Test car was a R33 series 2 - check wiring colors on other models before proceding

- Make sure all electrical connections are insulated

- make sure that all wiring is secured and cannot be damaged by normal operation of the car

Did this Mod.. worked like a charm.... the Car suddenly Came Alive hehe..

Anyways.. can u guys show me a pic of what you did or instruction.. on how u made a switch to turn the mod On and Off.. and another Thing

When i put my foot down, the needle on my Stock boost Gauge goes up to 3/4 or just little bit above that towards the full 1 Bar. So what PSI is my Car running on at the moment.?? only had my car for like a month.

P.S. ( I have HKS Filter and Full 3 Inch Turbo Back wif 4 1/2 inch Tip)

Cheers

SeSaR

Cost effective and easy way to leave the current setup (ECU grounds controller @4.5K) and have an override switch in the system, Is to place a diode inline with the ECU switched ground (0v) and the switch after the diode (see Pic). The diode will let the 0v from the ECU through but will block the 0v from the switch going back into the ECU.

(Warning! Diodes are directional, placed in this circuit the wrong way around will harm nothing but it will mean that the switch when on will send 0v to the ECU and when the switch is off the 4.5K rpm ECU output will not pass through the diode)

post-27968-1144543058.jpg

Why bother with all this passive relay / regualr relay stuff? A simple 3 way switch(PTT) will do just as good a job?

waiting for someone to shoot me down.....

  • 2 weeks later...

Ok I did it today, I've attached pics to show my wiring. The car to me feels like it's got more urgency through the rev range now. I've also attached a pic showing where my stock needle goes to, it does this straight away and holds there. Can anyone confirm that this is the right place for the high 7-8psi factory setting as it's been a while since I booted it and could just be mistaking the feeling of power for standard 4-5psi.

Cheers

PICS!

post-23873-1145591985.jpg

We soldered this and then taped it up.

post-23873-1145592054.jpg

Then we rubbed some paint off and bolted our earth to the chassis.

post-23873-1145592106.jpg

Here you can see how it all looks, pretty tidy.

post-23873-1145592140.jpg

And this is where my needle sits now...

post-23873-1145592181.jpg

Hope that helps someone, now can anyone confirm that this is the right place for the needle to be sitting.

very neat dan....

dont quote me, but i thought the wire had to be cut, not just tapped into like you've done?

I may be wrong, but thats how I thought it HAD to be done to work...

and your gauge is sitting on maximum vac....so that really has nothing to do with the high boost mod as far as i know

but at stock high boost the needle should be on or just above the middle slash on the boost side of the gauge....

LoL, I posted the wrong pic, here's the right one!

post-23873-1145593677.jpg

The red line shows where it sits.

Someone please confirm if it needs to be cut completely or tapped into is fine and if my neddle position is fine. shown by the RED LINE.

Cheers

if thats where its sitting on full boost BELOW 4500RPM, id say its working fine....thats about where mine sits....

my car showed 8.4-8.5 the whole way on the dyno run...and my aftermarket gauge shows 8psi....and my stock needle is about where urs is in that pic :pwned:

Awesome, feels like it's got more push through the mid range but just wanted to be sure.

I also just put some redline box oil in today too. I'll post about that the appropriate forum =)

Looks like my tap into black wire works too =D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey guys, Just want some advice on r34 GTT ac system. Since I’ve owned it, the ac compressor, doesn’t matter the set temperature or ambient temperature, runs for around 10 seconds then disengages the clutch, then re-engages everywhere 30 seconds or so and keeps repeating this.    is this normal?   I had it recharged today as it was slightly low and thought it would fix it but still does it. it cools fine in summer even prior to the recharge, except for the usual warmup when stopped or in traffic (still yet to wire overheat fan to on with ac)   any thoughts would be much appreciated 
    • To plug the hole. The engine plant may not have known whether the car it was going into had a gauge or not. It was a long time ago and the integrations might not have been fully modern. Or they might not have cared because the extra inventory and processes to save a few cents on the sender might have cost more anyway. But please tell me you are not still confusing the idea of a pressure gauge sender, and an oil pressure light switch. The switch will be out there. In a separate hole. Probably with only one wire running to it. Running the light.
    • Blower needs to go low on the exhaust side, displacing the AC and PS, which you have to decide whether you want to keep and how and where to relocate if you do. Electric option for PS is, at least, helpful. Sadly, there is no workable 12V electric AC of any value. Whilst the blower is the last compression step before the throttle, and so it might seem a good idea to have it near the inlet manifold (as mentioned above), you probably want it to go through an intercooler first, so, having it on the opposite side of the car facilitates that air flow path. The turbo discharges into the blower, so proximity of the turbo's compressor outlet to the blower's inlet is nice. But then you might want to intercool that too, before boosting it again....which would probably be a ball ache. Routing pipes out to the front and back could be a bit shit. If there was room for (at least) a small (but preferably larger) water to air core on that side, then that would probably be the best approach. I guess a reasonable alternative would be to locate the blower where the alternator is (more or less, associated with the inlet manifold, per Matt's thought), and somehow incorporate a water to air core into the manifold, sort of like they do for modern blown V8s. The big difference here though is that those V8s have only the one throttle (upstream the blower) and only the one compression step (the blower) and no need for too much in the way of bypass/blowoff valves. Whereas in a twin charged 6, you do need to think about one or two bypass valves associated with the 2 compressors and you would prefer to have the intercooling done before the air has to pass through the throttle. You'd like the throttle to work approx the same no matter what the compression is doing. But if it is located in hot air stream before a cooler, then sometimes the air will be real hot, sometimes it will be quite cool, and the throttle mapping/response will be quite different between those two cases. The throttle, if sized for hot air, would be too large for cold conditions. It's all a ball ache.
    • Package SC on exhaust side. Remote mount turbo. Still a fair bit of room when you get creative on the inlet side of the motor too. Especially if you can get really creative with the welding, and effectively build it into the bottom of the inlet manifold. Would definitely take some design work, and some trial and error, to make sure flow works well still! Might be easier to just start with the Nissan March though... All the work is already done for you...
    • I'll sit down and get a post together 😁
×
×
  • Create New...