Jump to content
SAU Community

Recommended Posts

My car produces a clicking or clunking noise whenever i change gears or take off from idle, if you take off very slowly you can't hear it but if you take off quicker you can hear it. Its coming from the rear end of the car, and its R33 series 1. Any help or advice appreciated. What could be the problem, has anyone else experienced this? Thanks.

Universal joint - it's a join that will move in "any" direction, and still maintain a solid connection. On a tailshaft, it's the bit that connects the shaft to the diff. As the diff can move (well, in non-IRS cars anyway) and so can the gearbox etc, the join must be flexible.

No doubt someone will have a pic floating around.

guys i had the same problem too.. when to two suspension specialists and still couldnt find anything wrong.. so i did a bit of investigating my self and found it to be my wires in the boot coming out of my subs and knocking against the body of my car.. i also found a pen in there as well as some screws lol... probably isnt the problem but worth having a look..?!?!

I have been to two different places to try and find the source of the clicking noise coming from the right rear of my car. Noone has been able to find it.

To a certain extent the car has always made the noise, and i have had the car for 4 years. Its nto the diff, fluids have been changed many times with no change, its not the uni joint as they have been inspected and found to be in better condition then aother cars in the workshop, and not susp as all my susp has been changed at on etime or another.... so i am at a loss to find the source of the clicking noise....oh and not lieky to be tools etc, as the time when it is easiest to hear is when pulling out of the pits with the concrete wall on the outside and the clicking noise reverberates off the pit wall, plus all the boot trim, spare wheel, jack etc is removed.

It could be anything, including the things i have listed as not being the source of the problem, only i couldnt be bothered throwing money at it when noone knows what it is....if you know the answer you could be the only one in the counthry that has fixed the prob. :(

Its one of those probs that haunts me :(

does it do it everytime you take off? could be just the brake pads moving on the pins, have similar click when i suddenly jump on the breaks... or the handbrake pads moving off...

just a thought

That noise will more than likely be driveline backlash. Not a major problem, just annoying. You can usually avoid making the noise with practice, and by being a bit smoother. And yes, you can do it with a button clutch :D

I suffer "driveline backlash" - when I push the clutch in suddenly - eg i was reversing out of a carpark and someone ran behind me - i get a loud clunking sort of noise. It feels painful for the driveline, what is suffering? Uni joints, diff?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Oof, I will forevermore have those shredded gears in mind whenever someone talks about showing mechanical sympathy towards their car. Thanks for the photos, fascinating stuff!
    • Curious to see how the SpeedTek stuff holds up
    • The holdups last year were drivetrain related. I had the car out right after getting the bearing issue resolved. Third launch and the car didn't move after releasing the clutch. It had sheared all the engagement teeth off the 1st gear.    Thankfully no other damage was done. I set an aftermarket gear beside an OEM gear and found that the engagement teeth on the OEM gear were much larger and better supported. Looking through my bin of spare transmission gears I found that there are two types of tooth on the OEM first gears - the larger tooth and the smaller tooth. It looks like most aftermarket gearset manufacturers base their design on the smaller tooth. OEM large tooth left - Speedtek, OS Giken, etc or OEM small tooth right Decided to give that larger engagement tooth a try. Pressed the ring off an OEM gear and sent it to a transmission manufacturer here in the States. They did their "faceplating" operation with my synchro ring on the Speedtek gear.   I reassembled it, took it back to the track and promptly destroyed the gear itself.  I'll rebuild this and use it as a spare - thankfully just first gear and the countershaft are damaged beyond repair. Definitely disheartening but my welded on engagement tooth ring held up!  Moved to Speedtek's dog engagement design as the gears appear to be much stronger. So far they have taken much more abuse at the track. Also scored a Stillway lockout from the Netherands for super cheap. It's for some other RB transmission so it took a bit of fabrication to fit but honestly a very easy job. I also had to heavily modify the gates as they were very different.   Then for some reason at the last test and tune a silicon coupler below the throttle blew off and took out the radiator and fan. Thankfully it was in the burnout box and not down track. This car is really beating me up - I still haven't made a pass in it. Ran it through the gears many times on the street but it keeps biting me at the track.  Currently in the process of replacing the radiator and remaking the throttle pipe to remove the coupler and use a cast 90 and a vband. I WILL get this thing down the track...
    • Covers most of the above points really. There's a few exceptions but most just see driving as an irritating but necessary task they must complete if they want to get anywhere on time. Also see it as a good time to show their awesome multi-tasking abilities on their mobile and/or doing their makeup.  
    • I don't believe I posted pictures of the second oil pump pickup I added so here they are. Data shows it gets oil pressure up to the relief pressure much earlier in the RPM. Is that important? Not likely... This was just another attempt to fix the bearing issues.   I also heavily opened up the inlet to the pump since it now had to flow oil from two pickups. I believe the diameter increased about 1/8".
×
×
  • Create New...