Jump to content
SAU Community

Recommended Posts

Hey guys,

Been watching these forums for the last year or so and have learnt a lot from you guys...

I recently had to take my baby off the road because I blew my turbo and a few valve seals (crankcase breather hose got loose and melted on my exhaust)!

I've rebuilt my turbo at GCG and now looking to do some head work - the question I got for you skyline guru's out there - I've got 2 alternatives that I got quotes for..,

1. Head service (general) + port and polish (inc. replacement of valve train - oversized) priced between $1500 - $1800

OR

2. Head service (general) + extra for any part of the valve train that needs to be replaced + tomei 257 poncams priced between $1000 - $1300.

Which of the 2 options do you guys recommend I choose? (Unfortunately my budget does not allow me to do both)

Note: my current mods are as follows: microtech ecu, blitz boost controller, GCG highflow stage 2 turbo(rated @ 500hp), front mount intercooler, Bosch in tank fuel pump, jecs high flowed injectors, 3" turbo back exhaust, 100 cell high flow cat, pod filter + an atmospheric bov.

Thanking you guys in advance ;)

Edited by Skud1988
Link to comment
https://www.sau.com.au/forums/topic/429798-r33-gts-t-head-rebuild-question/
Share on other sites

If you are just putting on a high flow and aiming for 260-300rwkw - Just service the head and put the rest of the money in your pocket.

Cost vs gain, you aren't going to see it. Spend money on brakes/suspension/tyres/clutch/diff or otherwise where you'll get far more bang for buck

  • Like 1

All I did with my head was get it cleaned up (sand blasted), Valve seats done, new valve guides and seals and cleaned the lifters

Added some Poncams and ready to go

If you don't mind answering, what power figures were you getting with that setup?

Engine isnt in the car yet

And that head setup will have little to do with the power figure, Turbo and supporting mods will really do more then basic head re-conditioning. The Cams will help a little but apart from that its all pretty standard

  • 7 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...