Jump to content
SAU Community

Recommended Posts

Either put a breaker bar on the crank bolt and get someone to hold it or lock it against something or the preferrable option is to put a bolt through in one of the bellhousing bolt holes and put a large curved lever in the flywheel teeth and use the bolt you put in as the levering point.

Does that make sense?

Rattle gun torque will do the job.

Don't give out advice like this to someone asking for genuine advice.

Either put a breaker bar on the crank bolt and get someone to hold it or lock it against something or the preferrable option is to put a bolt through in one of the bellhousing bolt holes and put a large curved lever in the flywheel teeth and use the bolt you put in as the levering point.

Does that make sense?

This pretty much. A large flat screw-driver can sometimes work as well. Screw 2 longer bolts (use bolts that arent part of the gearbox install) and then use a pry-bar/screwdriver between the 2 bolts and into a tooth on the flywheel to stop it turning. It's a bit hard to explain on here but you should be able to work it out

Don't give out advice like this to someone asking for genuine advice.

This pretty much. A large flat screw-driver can sometimes work as well. Screw 2 longer bolts (use bolts that arent part of the gearbox install) and then use a pry-bar/screwdriver between the 2 bolts and into a tooth on the flywheel to stop it turning. It's a bit hard to explain on here but you should be able to work it out

Why? Theres nothing wrong with rattle gunning it as in reality thats how the majority of people and workshops would have done it and have not had any problems.

No way in hell would I do them up with a rattle gun. Important parts that you dont want to fly off and cut your legs in half should be put on by the book. 1/2" rattle guns these days are getting pretty good and seen as the flywheel bolt torque is around 145Nm, i wouldnt want to put a rattle gun that is capable of doing double that on there.

I would find it slightly more acceptable to do the engine damper bolt up with a rattle gun, but I always do this up with a torque wrench

I never said do it on the highest setting Ive always used the 200nm setting, I would think its common sense that you wouldnt be pumping it to 800nm setting as some of the guns do go up to.

how do you know its the '200Nm' setting though? Keep in mind that what the shops air pressure is will play a part in it.

All good, everyone has their own way. I was just giving my personal opinion on the matter

Given how much care proper mechanics put into torquing things up in stages, it is hard to believe that anyone could believe that you could get a reliable torque to any proper setting with a rattle gun. How many thumps after it "stops" moving do you give it? How long after the compressor stops running is it going to give you the same torque? All the way to the point where it switches back on? Just for 3 bolts?

so im guessing the torque setting is 145nm on rb20det? ill have to try the two bolt pry bar method. I cant get to my front balancer bolt without removing the radiator.. dont want to make the job more harder than it needs to be. I'll have to buy another torque wrench, mine doesnt go that high. im guessing putting in new bolts is the go? i was thinking of running arp bolts in there? Thanks.

You should be right to re-use the old ones. ARP ones arent terribly expensive as well though

142-152Nm is the torque setting (for RB26) but they should all be the same. I use the torque setting on my flywheel in my 25 anyway

Don't do them up with a rattle gun. That is not good advice at all- there's a specific torque for bolts (especially critical ones) for a reason, and the flywheel is one of those places you want to it the right way. Re-using the bolts should be ok (providing in good condition), recommend using locktite though. I will come around this weekend with a proper torque wrench and give you a hand to do them up properly if needed, pm me if that'll help you. Andrew

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...