Jump to content
SAU Community

Recommended Posts

Well, I certainly had a good night.

Massive thanks to Ricky (xntrq) for doing most of the work in setting this up on behalf of SAU-NSW, and an equally massive thanks to the crew at Heasman's Suspension for putting on the feed, drinks and tech night.

Everyone, feel free to post your experiences here, add photos, and whatever else you can think of that was relevant to the night and what you learnt.

Aaaaaaannddddd GO!!!

Many Thanks Ricky for great organisation from our Exec table!

And what can I say about Heasman's!

What a superb Tech Night!

Thanks to Alan Heasman, Brad Heasman for setting this up as a great information night!

Plus the 3 talks given by Paul (Bilstein), Chris (Alignment) and Jonathon (Corner Weighting).

I was riveted to these talks but some of the cars there were definitely a 'distraction'!!!

And thanks to a great bunch of fellow SAU Members. Your behaviour as usual was exemplary...

The new Members deserve a hearty welcome too!

What a great night, learnt alot and how much more i need to look into my suspension.


Thanks to the SAU and Heasmans Steering for hosting this great night!



Here are my pictures =D



Well I had a fantastic night at Heasman's.

It is extremely rare to get an "all access" entry into a workshop like this so had to take full advantage of it by asking at least 150 questions through the 3 areas. I kept the guys on there feet with all the questions but walked out with a huge amount of new knowledge and i'm sure the guys in my group would agree :)

Some topics that really caught my attention were:

- How cheap yet how effective and over looked corner balancing is for a circuit car. A minute change can create a huge difference.

- The wheelbase and track settings for even a regular road car alignment which I have never seen a regular alignment shop look at.

- The huge number of shims and settings available for shocks

- A basic shock being totally upgradable rather than needing replacing.

- The temperatures and cavitation of oil in shocks

I very rarely get wheel alignments (4yrs gap in my Ute) simply because finding a reliable workshop to do a proper wheel alignment is near impossible but after last night I have now found that new workshop (even if it is a 146km drive and $25 in tolls :P)

It is extremely rare to get an "all access" entry into a workshop like this...

... :P)

Absolutely spot on Ben...

In '06 I was tossed out of a Sant A'gata Workshop by none other than Mr Winklemann whilst filming technicians on Lambos - lol > caught on film too > I should show it at the SAU Clubhouse one night

Many many thanks Colin for the photos :)

Having visited Heasman's the previous week I was extra excited for the tech night and it absolutely did not fail my expectations. You can really tell every single guy there knows their stuff which is very reassuring.

Here's a few of my pictures.

post-99360-0-13603700-1378517063_thumb.jpg

post-99360-0-48184700-1378517066_thumb.jpg

post-99360-0-89955100-1378517069_thumb.jpg

post-99360-0-59891000-1378517072_thumb.jpg

post-99360-0-78029400-1378517075_thumb.jpg

post-99360-0-07725100-1378517080_thumb.jpg

post-99360-0-31884700-1378517083_thumb.jpg

post-99360-0-29157600-1378517086_thumb.jpg

Thanks to everyone involved in organizing the night.

It was good to hear the information on setups from the professionals rather then some of the stuff floating around on the net.

Thank you Heasmans for the suspension education. Even the more difficult questions were answered on the spot regarding roll centre and bump steer. My highlight was the wheel alignment presentation and camber and toe angles for more street/drag oriented cars explanation. I know from past experience that wheel alignment perfection is an art form of patience. No more sounds like... [Wax] quick and careless wheel alignments for me.

What was also interesting is that they do roll cages in house too.

Thank you to Terry for the lift home afterwards.

Damn! Having worked next to a suspension shop when I was a second year apprentice, I learnt a fair bit. Suspension set up is an art form & I definitely didn't want to miss this!!! As Benm said about finding reliable workshops to do this sort of stuff (even a basic w/a), its hard to find a workshop that knows what they're doing, AND, its something you can't readily check. I'm with you Ben, its worth the distance for the best set up!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...