Jump to content
SAU Community

Recommended Posts

you're kind of killing your own arguement there though, if "The effect of opening the BOV is felt everywhere in the inlet tract within a couple of milliseconds of it cracking open." then the assertion "The BOV should be physically located close to the throttle body" - a cpl of milliseconds, it wouldn't matter where you put it, and so you could mount it whereever was most convenient and any performance advantage would be negligible if we're talking a couple of milliseconds.

this is interesting... my thoughts...

After the throttle body is closed, the system (between throttle body and outlet of compressor) is a pressured closed system correct? in a pressured closed system of air, it shouldnt matter where the "hole" is located cos the idea is to relieve pressure. Just like how the BOV is on the pipe at a 90 deg angle. As long as u have a hole somewhere in the system, pressure will be lowered.

However, in addition, I think GTSBoy is also talking abt airflow and this disruption in momentum if the BOV is located far away from the point of direction reversal. :)

Damn... How bad is it?

What would you do differently?

The afm is going to detect the returning air as the bov return isn't facing the turbo compressor at all. It will more likely go back through the afm and cause reversion.

The hose is just wrong. I would have placed the bov and return so they faced each other, so there was only a short hose with little bending.

Why is the intake smaller than the turbo and afm? I would have done 3 inch or 80mm, not 2.5 inch.

The afm is going to detect the returning air as the bov return isn't facing the turbo compressor at all. It will more likely go back through the afm and cause reversion.

The hose is just wrong. I would have placed the bov and return so they faced each other, so there was only a short hose with little bending.

Why is the intake smaller than the turbo and afm? I would have done 3 inch or 80mm, not 2.5 inch.

Too be honest I've done nothing to the car other than change BOV's.

Everything is left the way I purchased it..

I couldn't make the hose point upwards to get a smaller hose because when my bonnet is closed there is NO room at all..

Smaller intake in front of the turbo.. Too be honest I didn't really notice it was smaller.. :/

This is gay.... Haha

So where my BOV is plumbed back.. It should be facing towards the turbo, so it doesn't go back through AFM?

Too be honest I've done nothing to the car other than change BOV's.

Everything is left the way I purchased it..

I couldn't make the hose point upwards to get a smaller hose because when my bonnet is closed there is NO room at all..

Smaller intake in front of the turbo.. Too be honest I didn't really notice it was smaller.. :/

This is gay.... Haha

So where my BOV is plumbed back.. It should be facing towards the turbo, so it doesn't go back through AFM?

Nothing the the engine**

And as Scotty mentioned, the bov return should be angled so it points at the turbo.

Okay.. More welding & money.. :(

I'll grab a metal intake pipe as big as my compressor wheel? 3"

Weld on a fitting pointing towards the turbo and that BOV can only point up or down.. I can't turn it any other way, Bleh.. Lol

Thanks heaps for helping a noob import owner out :D

Really? I have the same bov and it swivels around, just loosen the nut on the back of the 2 bolt adapter.

No nut on bottom of adaptor?

You don't mean the one on top?

Before I put it on I tried moving it and gave up because I thought it was fixed on.

this is interesting... my thoughts...

After the throttle body is closed, the system (between throttle body and outlet of compressor) is a pressured closed system correct? in a pressured closed system of air, it shouldnt matter where the "hole" is located cos the idea is to relieve pressure. Just like how the BOV is on the pipe at a 90 deg angle. As long as u have a hole somewhere in the system, pressure will be lowered.

However, in addition, I think GTSBoy is also talking abt airflow and this disruption in momentum if the BOV is located far away from the point of direction reversal. :)

I think what you are forgetting is that the air has mass, so having to turn around and go the other way isn't the best as going out a bov close to the throttle body.

No nut on bottom of adaptor?

You don't mean the one on top?

Before I put it on I tried moving it and gave up because I thought it was fixed on.

There is a two hole nut on the bottom, correct? (where the entry is) The top one is just the air fitting.

  • Like 1

I think what you are forgetting is that the air has mass, so having to turn around and go the other way isn't the best as going out a bov close to the throttle body.

actually no... didnt forget that thats why i mentioned abt momentum as well.. which is why i agree that it shd be closer to the throttle body. :)

Damn... How bad is it?

What would you do differently?

Move the BOV about 10cm upwards so the hose only needs to be 1/10th that length, also use a hose that is the right shape (curved) so that it isn't full of nasty curves. The reality is no matter how backward your setup is it will still work fine, hell no bov works fine, but if you are going to spend money doing it, don't make it look agricultural spec like that, looks embarrassing to look at!

Move the BOV about 10cm upwards so the hose only needs to be 1/10th that length, also use a hose that is the right shape (curved) so that it isn't full of nasty curves. The reality is no matter how backward your setup is it will still work fine, hell no bov works fine, but if you are going to spend money doing it, don't make it look agricultural spec like that, looks embarrassing to look at!

I know hahaha I have a new hose on now that isn't kinked.. But same problem just after it starts making boost (when the screamer is about to open up) it feel like the car shifts down a gear..

For example: The feeling when you go from 3rd to 2nd at about 70kms??

So when the car makes boost it gets faster? That sounds pretty normal dude lol

Or do you mean when its already on boost it feels like the torque drops off at redline? if so that is normal, you get a big whack of midrange torque with the stock turbo around 4-6k then the torque drops off by redline as the tiny turbo can't provide any extra air. If you want that feeling to redline you need a bigger turbo.

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
×
×
  • Create New...