Jump to content
SAU Community

Recommended Posts

Not sure. I never sent him a clutch and they looked new.?

Haha. I paid for the box.

A mate had his HKS twin rebuilt by jb and it lasted and drive very well. So not knocking the guys work. It's just I didn't have much success with the heavy single with a mix of street and track.

I've told him 1100 nm and for safety he suggested solid centre clutch not as good on street but less likely to have issues, I touched on exploding subject and he said its the centre bit can't remember exactly but the part in middle of clutch plate that usually fails and it can't in solid for some reason? But the failures reported on this forum are mostly pressure plate related it seems ? Anyway I will ask him straight out tomorrow

Was it the clutch fault or some other part that caused it?

Buy a nismo copper mix and have piece of mind knowing your car won't be a write off

I have nasty photos of one that died (not my car) and won't use one because of them

I seriously doubt the Nismo copper mix is made by exedy.

Don't skimp on the clutch

yeah kind if agree here, its not something you want to have to replace too often....that said i picked up a refurbished NPC with flywheel cheap as chips and its been faultless....wanting the best doesn't always have to mean 2500$ worth of Nismo...just means you should do your homework...

Well I will let u know how I go, I've spoken to Jim again about the failures and to me seems fair enough , these things happen and I guess it's what insurance is for in the end, he seems very honest and open about the various subjects so I'm pretty sure mine will be fine. I'm sure other manufacturers have had clutch failures but we don't hear about them, anyways looking forward to 450kw at the strip

I think youd definitely year about exploding clutches on SAU. Especially the big boys, exedy, nismo, npc, os.

Anywho, you will need a twin for 450. It would be 10000000000x nicer to drive than a unsprung clutch. Imagine taking a sledgehammer to your gearbox with every gear change. That is what 4500lb clamp load sounds like haha.

Go nismo or NPC. Both have good rep

Yep that's what he said, u guys have me suitably worried now... Is it true the excedy twin plate is same as nismo? There is one going for a good price I know of

no the nismo clutch plates are made by velo, but I doubt they are allowed to sell them to anyone but nissan/nismo

Funny. You ask the question and hear not so good revues, then do your own google search, find more horror stories and still go with mega clamp solid centre single? Make sure you have a spare gearbox is all I'll say.

Good luck

I hear you... I really do. But there are stories of nismo, npc and others letting go too, please don't think I havnt considered your suggestions but in talking to Jim he was happy to explain what happened and my tuner hasn't had any issues so I just decided to go with my original plan but actually the only horror stories are in sau in the wider google search nothing of note came up under my search queries anyway I hope u don't get to say I told you so buy time will tell

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...