Jump to content
SAU Community

Recommended Posts

my Nur had Nismo injectors before i changed, they were fine for 350'ish rwkw, running 2530's.

Proven, solid injector. I'm in Melb as well. I'm sure i can help you out with a good price just to get you passed these injector issues :)

I tryed to pm you but it won't work just keeps giving me an error message. Don't know what's up. Are the nismo injectors going to fit in my 32. And are they the same cc because I can't tune yet haven't got power fc.

  • 2 weeks later...

Hey guys I purchased a power fc and controller and second hand denso 550cc injectors

I was just wondering if I can put the injectors in now without the power fc because all the workshops are closing up for chrissy. Will it still run ok or should I wait till power fc gets installed and tuned? Thanks guys

Hey guys I purchased a power fc and controller and second hand denso 550cc injectors

I was just wondering if I can put the injectors in now without the power fc because all the workshops are closing up for chrissy. Will it still run ok or should I wait till power fc gets installed and tuned? Thanks guys

You can setup the injectors in the PowerFC, but you'll need to know the latency of the denso 550s or the idle & low throttle fuelling will be off. Also, you'd be taking a bit of a gamble on the motor if you drive it hard before getting the tune checked after the injector swap.

I would be getting any S/H injectors flow tested before fitting them, injectors sometimes don't like being removed from a fuel system and left on a shelf for a few months. Were they stored in a sealed bag or similar at least?

One slightly blocked injector can really ruin your day... I hope you got them cheap as new injector prices are dropping fast.

Yer the guy took em out of his car cloth baged em bubble warped and boxed and express posted them hense why I was thinking of putting them in the car straight away. I can't get the car booked in till the 6th of jan so I wasn't sure if the injectors will be ok sitting till then or is there a good way to store them ?

Not really, just keep them in a sealed sandwich bag or similar. I would replace the 'O'rings too if they have any sign of damage, and lube them up well before installing them, you don't want petrol leaking over a hot engine.

I use a little silicone spray to lube the Orings..

  • 4 weeks later...

ok so injectors in power fc in tuned and dyno'd came back with 245kw on 14psi

feels much nicer to drive has realy changed how the boost comes on its a bit more punchy,

im thinking i might need some more mods soon tho to gain a bit more power 300kw would be nice i think :)

ok so injectors in power fc in tuned and dyno'd came back with 245kw on 14psi

feels much nicer to drive has realy changed how the boost comes on its a bit more punchy,

im thinking i might need some more mods soon tho to gain a bit more power 300kw would be nice i think :)

All you need is 22psi crammed down it's throat, as long as the fuel system can keep up. Seems to be making good power for the low boost you are running atm.

Having some problems at the moment guys hoping some one can help, I was driving home this arvo and stopped got fuel, drove like 10ks car started spluttering losing power for a second then come good, keep driving same thing splutter a bit then come good. Then I'm doing 80 up hill and it just keeps dropping power and I pull over off the road and it just stalls started up again stall, start up again keep driving not too bud a couple of little splutters then get to the end of the street turn the corner and stall in the middle of the road got it home but worried what it may be dirty fuel pick up from when I fueled up, coils, afm

Any help would be muchos appreciated

Well lets go through process of elimination.

Car drives good -> Stop -> Fill up -> drive off -> car is shit

In conclusion, all evidence points to the variable that you exposed yourself to, the fuel. Therefor empty tank with syphon, go to good petrol station, put in fuel and see if that was the problem.

Well I filled with bp ultimate as I usually do, the fuel light wasn't on its not like the tank was bone dry picking up all the shit at the bottom. And I'd have thought it would caugh and fart within a few minuets of driving if it was bad fuel or shit from bottom of the tank. It used to have a little bit of a loss of power moment before I got the injectors and the ecu done but my mechanic said that looked to be a faulty relay for the fuel pump and they replaced it.

if your car was driving 100% before you filled up.

I dont see how something coincidentally broke at that exact moment unless you mistook your engine bay as the fuel tank.

Also, when you fill up, it sloshes around and mixes together. Its not a layering system

running a tank dead dry will not allow the pump to pick up dirt lol where do you think the sock sits that picks up the fuel? I can tell you now it aint at the top of the tank or you would never drive long enough to see the gauge drop

Take the car back to the dyno if it can be driven and get it on there to see what its doing. Sitting behind the laptop is not going to sort it out any time soon. You have said ages ago that the car used to splutter and stall and clearly the mods now done to the car have not changed anything so there is something else that needs attention

Who tuned it?

With regard to turbo upgrades, take a look into the new Precision Turbo GTR replacements. From what i have seen they should be good for some pretty decent power. Just run them at low boost ;)

Edited by ido09s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I can ship Nismo floor mats to you: https://www.oemsoko.co.jp/products/nismo-floor-mats-for-skyline-r33-bcnr33-stagea-wgnc34?_pos=1&_sid=9278c1467&_ss=r  
    • Here's the link: https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6642/misc/G49?frame_no=WGNC34-137122 What you think about it? The same product i found on nengun: https://www.nengun.com/oem/parts/40567/MiPwn5qAMfCfmpxHNDnwn5q9MDAx8J-QiW9sZC1qcC0xMTAtRzQ5LS0wMDE/Floor+Carpet+%2F+Mat+2/0688339eba149c19 Bot i have spoken to 😅 ensured me, that mats are 100% original, oem product. I have my doubts. I also heard what you mentioned, that nengun often offers items that are actual not available... On the other hand mats i found on japanese yahoo or ebay are in poor condition and still quite expensive so i'd rather wait for some better offers. My location - Poland. We literaly don't have ANY market for used Stagea parts so need to search outside Europe.
    • You can’t see much on the other side as the lcd is there I don’t think it’s the same as the m33 beside it as the markings on top is not the same was hoping someone had a good quality photo or if they just happened to have the unit in hand, quickly take the cover off and take a photo to clearly show the marking on top to identify the diode   the unit is currently with an electronics repair shop so I can’t take another photo at the moment hopefully they are smart enough to know if it’s a zener diode or not
    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
×
×
  • Create New...