Jump to content
SAU Community

Compression Test

morto86

By morto86,
in General Maintenance

 Share

Recommended Posts

Missileman Veteran

Missileman

Posted
Posted (edited)

On a warmed engine with all sparkplugs removed, with accelerator fully depressed and a charge on the battery capable of cranking the motor at 300rpm.

RB20DE/T/26DETT

New = 170psi

Low Limit = 128psi

Max cylinder difference 14psi

...from engine workshop manual.

Edited by Missileman
Ben C34 Grand Master

Ben C34

Posted
Posted

I just got the reply 210. Cold. Does this mean the head has been shaved previously

No as the comp ratio doesnt effect the compression test. it just ensures the rings and valves are sealing as they should.
Ben C34 Grand Master

Ben C34

Posted
Posted

Def 200 all round with snap on gauge and warmed engine. With researsh this proves the comp ratio therefor is 10:1. As for the knob who said the comp is not relayed to the ratio. Actually write out the equation.

Settle down. explain to me how an engine when built has a certain compression test result, then when worn had a lesser compression test result? Did it's comp ratio drop? can you run more boost cos it has less comp ratio? NO. explain how comp ratio effects the comp test results please :)
KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Settle down. explain to me how an engine when built has a certain compression test result, then when worn had a lesser compression test result? Did it's comp ratio drop? can you run more boost cos it has less comp ratio? NO. explain how comp ratio effects the comp test results please :)

Well personally I would have though it was obvious that the higher the compression ratio the higher the expected compression test result . The value of the compression test for measuring wear depends on knowing the original compression so as above if the stock factory figure was 170 psi then yes 130 psi indicates a lot of wear which can be confirmed with a leakdown test. My engine had 130 psi compression when built because of the choice of pistons (CR about 8:1) and leakdown test is within limits at 5%

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • Dose Pipe Sutututu
      Chris' Toyota Mark ii JZX110

      By Dose Pipe Sutututu · Posted

      I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...