Jump to content
SAU Community

Recommended Posts

So here's the deal guys.

I've got oil spraying out of my dipstick tube as well as pushing my dipstick out of the tube about 150mm each time.
so clearly im getting pressure in the crank case

but ive tried all i can think of now im out of options, so far ive:

-replaced the PCV valve with a new genuine unit from nissan.

-checked all breather hoses to make sure they weren't blocked.

-done a compression test to make sure i wasn't getting excessive blow by that was causing oil to spray out. (read 140psi across all cylinders)

now thats where ive hit a wall..... i cant think of anything else to check =\
any ideas?


appreciate any help...thanks.

Link to comment
https://www.sau.com.au/forums/topic/435182-oil-spraying-out-of-dipstick/
Share on other sites

just went and checked the rubber is pretty hard around the seal but its still fitting pretty firm

surely though that shouldnt justify oil spraying out of the tube right??

well damn i hope thats not the case.......

im not getting any smoke blowing out the exhaust so thats not looking likely in my case but i might still look into that if i cant get it sorted otherwise

Doing a comp test is all good & well for an N/A application, BUT, what's to say your rings are not responding when boost pressure is applied? The only way to truly cancel out your rings would be to do a cylinder leak down test.

I build, run & tune LARGE turbocharged stationary engines. I've encountered this issue before. Customer complained about an oil leak. Discovered to my surprise when going from idle to load @ about +10''Hg (max is 30Hg/14.7psi)) crankcase pressure was going from -.5'' H2O to +25'' H2O & popping both dipsticks along with twin fountains of oil till the rings responded at about +15''Hg then everything would settle down. This particular engine had issues rejecting heat through its heat exchangers, its dump radiators were too small & subsequently had alot of high jacket water temp shutdowns.

Piston rings hate heating up & cooling down. if the temps are high enough, over time, they start to lose their tension & don't respond very well to pressure changes.

Pressurizing your crankcase to the point of popping the dipstick out can only come from one place. The only other thing I can suggest as 'for the time being' fix is to get a little bit of heat shrink (for wiring), place it over the rubber, heat it & refit your dipstick to stop it popping out. Then just hope you don't start blowing out other seals!

I was just going to suggest a leak down test. :yes:

140psi compression test result isn't brilliant, especially if that was after cranking for a while. Do you have a catch can fitted?


I got similar problem whereby if I park my car on a hill it burns oil out the tail pipe...

Valve stem seals?

Doing a comp test is all good & well for an N/A application, BUT, what's to say your rings are not responding when boost pressure is applied? The only way to truly cancel out your rings would be to do a cylinder leak down test.

I build, run & tune LARGE turbocharged stationary engines. I've encountered this issue before. Customer complained about an oil leak. Discovered to my surprise when going from idle to load @ about +10''Hg (max is 30Hg/14.7psi)) crankcase pressure was going from -.5'' H2O to +25'' H2O & popping both dipsticks along with twin fountains of oil till the rings responded at about +15''Hg then everything would settle down. This particular engine had issues rejecting heat through its heat exchangers, its dump radiators were too small & subsequently had alot of high jacket water temp shutdowns.

Piston rings hate heating up & cooling down. if the temps are high enough, over time, they start to lose their tension & don't respond very well to pressure changes.

Pressurizing your crankcase to the point of popping the dipstick out can only come from one place. The only other thing I can suggest as 'for the time being' fix is to get a little bit of heat shrink (for wiring), place it over the rubber, heat it & refit your dipstick to stop it popping out. Then just hope you don't start blowing out other seals!

some really good info there thanks man

probably an easy fix there with a bit of heat shrink, but im not looking for a cheap fix here id rather get it sorted properly

and like you said id likely start popping seals lol....read up on another forum some guy just clamped the tube with a pair of vice grips :mellow:

looks like i should defiantly go ahead with a leak down test then and see how shes looking

I was just going to suggest a leak down test. :yes:

140psi compression test result isn't brilliant, especially if that was after cranking for a while. Do you have a catch can fitted?

Valve stem seals?

nah mate no catch can....... would be curious to see if im getting anything blowing out through the breathers as well as the dipstick now that you mention it

defiantly worth doing then if you think it will help
being that the breathers run back to the intake though wouldn't that cause a vacuum in the lines from the pcv valve and through the breathers though??
hence its at negative pressure anyways?.... thats just a guess


haha well lets just say
I've got a heavier foot than brian o'connor.... pretty hard

Antz. U thinking a vented can?

yup..would have to be...you could just stick little filters a top your cam cover vents , but this will most likely spray oil everywhere...

anyway, to keep it simple.. if can is vented, block pcv...if can plumbed back to intake, retain pcv...

i could tell you not to drive it so hard but you would probably laugh at me :P

If u need bud I can make u a vented can. But me thinks ur problem will be increased buy the -5s u just bought. Enjoy.

haha i know right.... thats why im tying to nut this out before i chuck em on

shit timing how it kinda came up the day i paid for them :glare: ...... lol

you do some fabrication work do you?

i actually do think i "might" have a catch can off my old 33 in the garage somewhere

ill have to have a look ....but otherwise ill get back to you about that one :)

A catch can won't really help, you'll only be increasing the size of your crankcase a little. If a leakdown test fails to show where the problem is, then testing on a dyno to actually measure the crankcase pressure is what will be needed.

In my previous post I mentioned a water column measurement: +25" H2O. This is only about 1 PSI. It was an 18 litre 6 cylinder. It didn't take much pressure to lift the dipsticks. Just letting you know even a little pressure loss can do big things.

When you do a leakdown test, try to test in KPA not PSI.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...