Jump to content
SAU Community

Recommended Posts

Is cracking of the rear subfram a common problem for our cars? Just changed the drivers side rear wheel and noticed a massive crack, just above the driveshaft. Same on the passenger side.

Has anyone had this issue, if so, how much to replace the subframe??

Trying to get a hold of the previous owner but no luck. Will be contacting the RWC workshop asap.

Link to comment
https://www.sau.com.au/forums/topic/436170-m35-cracked-rear-subframe/
Share on other sites

Dont weld it. Its the devils glue! There is nothing that sscchhdicky tape can not fix! (guido hatzis quote)

Let the baguette jokes and welding jokes begin!

Edited by Howaitonaito

Not fussed about price, the car was issued a rwc wen it clearly wasnt roadworthy. Previous owner had no idea either.

Small things werent done, cv boot and globes, was willing to let it slide because theyre easy fixes but after seeing the subframe this arvo im not even sure the workshop looked at the car.

Front pads are cactus, discs are glazed, front right cv boot is completely torn, number plate globes werent replaced AAAND the subframe is cracked.

Where do i go next? I want this all fixed, not by the workshop that issues the rwc and i dont want to pay a cent for the repairs..

Santa Claus by the sound of that. Your dreaming if you think a workshop is going to pay to do that for you.

Two options.

Weld it. The whole thing is welded together anyway.

Or

Buy one, second hand or new. Try 55400-AQ500. Sit down for the price.

It wasnt noticed. I only saw it because i had a flat in the rear. To the wheel off and its the first thing i saw.. spent all morning on the phone, just gonna swallow this bitter as f**k pill and fix it myself.

Not letting the rwc workshop touch my car again.

Trust me i spent the whole morning ringing vicroads, vacc, consumer affairs even the dodgey prick that issued the rwc. Its a shit storm waiting to happen and i really cbf dealing with it.

Its not the end of the world, swap the subframe, fix a few stupid issues get another roady bang, problem solved.

Shit happens, assholes cause it!!

But you must bring the assholes down like a bag of $hit! I wouldn't let the shop that issued the rwc get away with it. I love conflict and causing it. Bring the phucker down I say!

Oh back on to topic, get a replacement frame from Scott, I think he's swapped out quite a few so he'll be able to offer you tips and tricks too.

Its much easier said than done, if the last few years has taught me anything its that karma does catch up with you lol.. hopefuly he stubs his toe real bad!!

I love conflict to but its my car and i want it on the road asap, dealing with it like many have said isnt gonna achieve that.

Yep got onto the m35 bible with legs (scott), with any luck its sorted soon.

whats wrong with welding the cracks if its don't properly? The rest of the subframe has welds all over it!!!

I think i've had this agument before.........

+1. A quality weld job will be as good as a new one.

Any pictures of the cracks?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...