Jump to content
SAU Community

Recommended Posts

  • 1 month later...

So end of year wrap up, rexmas, village, elsewhere? Will try to pop down Sandown Saturday for a chat/taxi ride :-) as no car.

WRXmas this weekend, plus monthly meet at il.tavo on 10th Dec.

No car? What've ya done to the '14?

  • 2 weeks later...

When is the next track day?

Can NSW club members enter?

You certainly can enter... however we've just finished up our motorsport rounds for the year... I think the next ones that we'll be doing will be in Feb...

Repost from the last meeting thread for whoever is following this one (and to put John out of his misery hehe)

No idea what is happening on the presentation/trophy front but here are the results none the less...

Overall - Adjusted Total (Best of 6 Rounds)
1  John Packham       Nissan 200sx s14     50
2  Aaron Barnes       Nissan R35 GTR       48
3  Dave Marinucci     Toyota 86            40

Class A - Mod 4WD
1  Aaron Barnes       Nissan R35 GTR       54
2  Craig Ferdinands   Audi RS5             28
3  Paul Stephenson    Nissan Skyline       12

Class B - Std 4WD
1  Chris Madden       Nissan Skyline       32
2  John Richardson    Mitsubishi Evo VIII  17
3  Craig Ferdinands   Audi RS5             16
=  Michael Brne       Nissan R32 GTR       16

Class C - Mod 2WD
1  John Packham       Nissan 200sx s14     51
2  Andrew Collins     Nissan R31 Skyline   30
3  Jamie Graham       Nissan Skyline GTS   14

Class D - Std 2WD
1  Dave Marinucci     Toyota 86            52
2  Ash Cosgriff       HSV Clubsport R8     36
3  Justin Connell     Nissan Skyline       14

Class E - Open
1 Chris Thomson       Nissan GTR           12

2014_ClubChampionship.xlsx

  • Like 2
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...