Jump to content
SAU Community

Recommended Posts

So did you push the car through some corners? Understand if you didn't as its not your car ;) On tighter tracks an evo is leagues ahead. On a more open track the Big R will lay waste to an evo HP pending of course lol

I did and it does. Though my car is pretty much set up properly as well.

Edited by Mick_o

As an owner of 3 Emos previously (6, 7 & an 8) and now have an R33 GTR I'd say go the GTR! But... and it's a big butt:

You need deep pockets to run a GTR as they have huge weight & power & that equals many sets of tyres & brakes. Plus they arent cheap to fix/maintain full stop.

The Evo's only ever lasted 6 months & I got bored. the 6 speed gearbox made the 8 so much better than the 6 & 7 I had but the handling was still 1 dimensional & boring on a track. However, on the road the Evos are more playful & more fun for it than the GTR by miles! The GTR feels too big & slow to respond...

Not sure I've helped here...

My work is done.

Not at all lol

The car will be mainly used for track duties with the odd occasion of going for a cruise. Ive come to the conclusion that I need to just go and drive a couple, I'm sure one will jump out at me more then the rest.

Ordinary is that your GTR videos on YouTube ?? Ordinarydriver ??? I assume it is.

The only thing that sways me to a EVO is the cost of running and mechanical strength at the track. Cheaper to run, cheaper to fix and just as quick.

But then again GTR's seem pretty bullet proof upto 250awkw, besides the oil starvation issue at the track and filling upto the bump in the stick seems to fix that problem.

Last thing I want is to spend around 20k on a car then need to spend another 10k on an engine rebuild in a year or so. This is where the Evo seems to have the edge in reliability. But then again anything can happen at the track.

The only thing that sways me to a EVO is the cost of running and mechanical strength at the track. Cheaper to run, cheaper to fix and just as quick.

But then again GTR's seem pretty bullet proof upto 250awkw, besides the oil starvation issue at the track and filling upto the bump in the stick seems to fix that problem.

Last thing I want is to spend around 20k on a car then need to spend another 10k on an engine rebuild in a year or so. This is where the Evo seems to have the edge in reliability. But then again anything can happen at the track.

How much have you tracked before if you don't mind me asking?

A stock gtr vs stock evo umm yes an evo is leagues ahead. .. A Stock GTR is a nugget ;)

Only cos Nissan got lazy and sat on their asses. Look at the incremental development with the evo over the years and compare that to the GTR. An R34 isn't that much better over an R32.

& of course your 9 is a couple generations younger than even the latest model R34.

Evo doesn't hold a candle to a GTR in terms of road presence too.

Dollar for dollar though, evo does win hands down. A 20k evo 8 would go a lot better round a track than a 20k 32GTR.

I 100% agree with that mate nothing says gtfo of my way like a GTR does on the road and on the track too! :D

I might be slightly biased to an evo owning 1 But pretty much all my mates own gtrs and i LOVE THEM so dont think im hating on GTR'S for a second here but im sorry reality is an evo is a better track car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...