Jump to content
SAU Community

Recommended Posts

When i accelerate at the green lights after coming to a stop, people around me are always going faster then me and so i compared my rpm to their rpm when accelerating from the green light is they often always rev up to 3300 rpm as this is what it takes for my R34 to keep up with them side by side

I usually rev up and cruise after the start of green lights constantly at 1500 - 2000 rpm because anymore then that my engine feels like its wearing itself out and burning unnecessary fuel as my engine always gives off this whooshing sound after 3000 rpm and roars loudly within the car's cabin. (oh and i usually smell fuel within the car after revving it up to 3000)

Whats weird is that i tested beside cars such as old camrys, corollas, Mazda 3s and 8 etc and they are driven by mature aged people and they drive hard up to 3300 rpm usually.

Yet even after revving it up to 3300 rpm cars behind me still stick close expecting me to go faster even when i'm on the left side of the road.

Oh and i forgot to add, i rev to 2500 rpm and constantly stay there gets me to 40 - 50 km slowly and i mean very slowly like around 6 seconds and that every car overtook me like i'm driving like a grandma.

Edited by Elegant Skyline

Seriously

the engine is most efficient at 7000rpm , so that's where you need to be all the time.

Its why the R34s have tiptronic, you can manually select the gear to get you closest to 7000rpm

When i use my tiptronic i often smell something burning so i don't use it plus i don't want to go over 3000 rpm as it seems too much for me.

Fuel needle drops like a rock when i reach near it.

Even then i stick to the speed limit and keep getting bad fuel economy.

Most efficient?

So i would use up to nearly half my fuel tank just to go the city and back at Liverpool?

I wonder if any tuning will give me better acceleration below the 2500 rpm range but be economical.

22's = more efficient tyres. Just ask the tyre joint for some.

Sounds like you need to remove the stupid mods and get someone to look at the car. Have you checked for boost leaks?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...