Jump to content
SAU Community

Best Complete Front/rear Diff And Trans Upgrade For A 32 Gtr

boobeedoobee
 Share

Recommended Posts

Piggaz Grand Master

Piggaz

Posted
Posted

Quaife or Nismo front, same again in the rear and extra few friction plates in the transfer case, commonly known as "the transfer case mod".

Prob looking at $1800 ish to do the front, around the same for the rear and $600 for the transfer.

  • Like 1
Link to comment
Share on other sites
chez00 Contributor

chez00

Posted
Posted

^parts prices only, right? The quaife front LSD goes for around $1850 without install or bearings or seals.

The setup Piggaz has suggested would give a great setup for OPs application though.

  • Like 1
Link to comment
Share on other sites
chez00 Contributor

chez00

Posted
Posted

Was also thinking a billet centre plate in the gearbox is not a bad idea. This would prevent shock loading and shaft separation in the gearbox on hard launches at Collingrove. I see you're in Adelaide - feel free to contact us if you'd like any further info.

  • Like 1
Link to comment
Share on other sites
GTSBoy Grand Master

GTSBoy

Posted
Posted

Centre plate is for the gearbox. No need to change the other gearbox internals if they're working and you're not making spastic power. If eother of those are not the case, then you have a bazillion different upgrade options out there, ranging from $100 for different oil to $20k for a special special box.

  • Like 1
Link to comment
Share on other sites
JimmyRickard Mentor

JimmyRickard

Posted
Posted

Quaife or Nismo front, same again in the rear and extra few friction plates in the transfer case, commonly known as "the transfer case mod".

Prob looking at $1800 ish to do the front, around the same for the rear and $600 for the transfer.

who does the transfer case mod in Sydney?

Link to comment
Share on other sites
boobeedoobee Community Regular

boobeedoobee

Posted
  • Author
Posted

^parts prices only, right? The quaife front LSD goes for around $1850 without install or bearings or seals.

The setup Piggaz has suggested would give a great setup for OPs application though.

What's OPs application?

Link to comment
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

OP's purpose is "Hillclimbs mainly and the occasional time attack ", OP.

I'd also leave the box until you need to change it, and when you do get a dog box in there for the quicker shifts :)

Jimmy anyone can modify the transfer case, it involves adding the correct number of additional clutch plates to preload it. Award did mine.

  • Like 1
Link to comment
Share on other sites
omnigear Proficient

omnigear

Posted
Posted

N00b question , what is this center plate upgrade?

Centre plate is for the gearbox. No need to change the other gearbox internals if they're working and you're not making spastic power. If eother of those are not the case, then you have a bazillion different upgrade options out there, ranging from $100 for different oil to $20k for a special special box.

Link to comment
Share on other sites
chez00 Contributor

chez00

Posted
Posted

The stock centre plate of the RB25/6 gearbox can flex in high torque, high grip situations such as aggressive launches or high speed cornering. When it flexes the shafts (mainshaft and countershaft) come out of alignment and the gears destroy each other. The billet centre plate improves case rigidity. It's basically a full rebuild to install, so would be done with a bearing and seal refresh as a minimum, check synchros etc.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      rb20de neo +t conversion - boost pressure sensor needed?

      By GTSBoy · Posted

      You're confusing two different responders and more than one issue. The stock Neo ECU boost sensor is used by the ECU for protection purposes. It is essentially only an overboost sensor. It is not used for determining engine load for fuelling or ignition purposes. That task falls solely to the AFM. Any aftermarket ECU that either has an onboard MAP sensor or a plug in one, will use the MAP sensor as the primary load sensor. Or I should perhaps say "can", rather than "will", because some of them have the option of using other primary load sensors. That MAP sensor is not for the same function as the stock Neo boost sensor. The reason I recommended against a plug and play ECU is that they are intended to run a particular engine and usually in the car that the particular engine came in. So, if you have a transplanted engine in a different car, with some parts of the original missing (such as the boost sensor, for example) and therefore likely non-standardness of the loom and its insertion into the car's loom, then it is very likely that you will run into the same problems with needing to fix up wiring to make it work that you would with the stock ECU. And, if doing so for the stock ECU is enough of an obstacle that you start considering a standalone plugin as a solution, it should become clear that the plugin is quite possibly not the solution you'd hope it to be. It would just lead to more of the same type of problem solving work to get it going. In the above paragraph and in my earlier post, the lack of the boost sensor is not critical. It was just used as an example of something that we knew you did not have right, such that the stock ECU would not work. I took that as an indicator of a reasonable probability that there were other related problems hiding there.
    • GTSBoy
      R32 GTR fuel gauge not working despite fixing fuel level sender

      By GTSBoy · Posted

      I can think of two places in my city of <1.5million population that specialise in automotive instrument repairs.Unless you're out in the wilds of Quebec, you have 3 major Canadian and 3 major US cities within the same distance as the single nearest city to mine. Surely there is somewhere you could send it.
    • TurboTapin
      Can anyone shed some insight on this Turbo?

      By TurboTapin · Posted

      I never cared for twins but whenever these conversations came up, I always presumed the higher number represented a larger turbo. Learn something new everyday. 
    • joshuaho96
      how do i install this 3 port mac valve for boost control?

      By joshuaho96 · Posted

      Interesting, I've never seen a failure like that before but with the age of these cars and the general questionable-ness of all kinds of parts these days you can't rule anything out I suppose. Boost leak testing the boost control system would've revealed this though.
    • Duncan
      how do i install this 3 port mac valve for boost control?

      By Duncan · Posted

      Thanks for updating the outcome; while anywhere in the system could leak, I hadn't heard of a wastegate actuator doing so before, can add that to the list of potentials for next time
×
×
  • Create New...