Jump to content
SAU Community

Recommended Posts

Fuel will definitely still come out with the vac lone removed from reg.

Perhaps that could solve the problems, spray car with fuel, light, turn 360 and walk away...

HAHAHAHA.

I think you meant 180.

I bet your fuel pressure regulator has a hole in the diaphragm and is sucking in extra fuel under vacuum. Remove the vacuum line from the reg as the car is running and I bet you fuel pours out. As a mechanic, I've seen this several times on Falcons and the symptoms are exactly as you describe. Also, I've seen gas systems that keep the fuel pump running, even when switched to run on LPG, (they just cut the signal to the injectors) so the rail would still be pressurised and the hole in the fuel reg diaphragm would still be sucking in more fuel.

This sounds spot on, the fuel pump does keep running when its switched over to LPG, when I took the manifold off to put some new injectors I found some large pools of liquid too, was still there after a few days sitting so not sure if it was fuel.

When It would start playing up was after cruising for a while and coming to a stop at traffic lights, then after flogging it for a few minutes it calmed down a bit but still rough. Im going to get a new reg to rule this out and see how it goes.

The last few days its behaved itself, ive got 15L/100kms on petrol and 17L/100kms from LPG, so its come down a bit and ive blocked the vacuum lines near the Map sensor which are the blow by return and fuel vapour lines.

I was a Ford mechanic for a few years. I've changed 6 TPS's in my time there due to a flatspot, cutting out, running rough. They tend to wear out right on the cruise spot, where it sits most of the time.

Check with a multimeter. Unplugged, check resistance from idle to WOT. If connected, probe & check voltage from idle to WOT.

In both cases of diagnosis, you'll see zero volts or infinite resistance when you hit the spot.

I couldn't get any volts or resistence with my tester but autoelectrician said on his tester it was showing response to the throttle, ive bought a new TPS just incase its playing games on me, It does seem to happen at right at that cruise spot where the

throttle is hardly open.

So will next replace Coolant sensor, TPS and fuel regulator and see how it goes. If still playing up will consider an exorcist or lighting it up and pushing it off a mountain.. lol

Some pics for those interested,

post-70965-0-47117600-1399078171_thumb.jpg

These are the Map sensors, the orange Map sensor is from my other Dedicated LPG ute ( Genuine ford, made in Germany), the blackish one from the tickford ( made in Italy), not convinced the tickford one is faulty but swapped it anyway,

post-70965-0-69990800-1399078312_thumb.jpg

Edited by AngryRB

Ive replaced the TPS but the coolant sensor snapped off and half of its stuck in the head still, unbelieveable place to have a sensor, can't get a spanner on it cause of the way it sits.

Havnt got round to the Fuel reg yet, all these sensors are eating my $$$ up, and its been running without any black smoke or stalling for about 500km's now, so for now just waiting and see.

The engine seems to have constant tappet noise and recently noticed some noise that occurs under load hot and cold, its sounds like in the cylinders, probably the start of piston slap , took the oil cap off while it was running and seems to be a bit of blow by, wondering if the blow by return (which ive blocked) could have been messing with the map sensor which sits close to it. funny how since I

blocked the blow by return and fuel vapour return it hasn't missed a beat.

  • 3 weeks later...

So I think I finally have the answer, Someone had got mixed up the Vapour line and the Fuel return line on the fuel pump,

The vapour line has a restrictor to stop fuel from flowing to the charcoal canister, which had a few hundred ml's of fuel in it when I pulled it off, so fuel was being sucked into the manifold and pooling there , when on light throttle

the vapour was causing overfueling and stuffing up the Map sensor probably. So finally got to the bottom of it, so anyone using a shitload of fuel , check the fuel pump was plumbed up properly.

last fuel consumption was around the 11L/100km, which is a big improvement, I wonder if the return line being plumbed into the restrictor was causing higher fuel pressure in the rail too but not sure.

thanks for everyones input and help.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...