Jump to content
SAU Community

Recommended Posts

1990 R32 GTR RB26DETT - $22,000 ONO - 0422626173



Up for sale is my 1990 Nissan skyline R32 GTR, It is in great condition with 84,000kms and the original japanese service books, it has been used as an occasional weekend car.



Panasport G7 C5C 3 piece wheels with Federal 595 RSR 255/45/17 (1500kms on tyres)



Greddy Type S Coilovers



Cusco rear camber arms



Cusco castor rods



HKS pod filters



Greddy Cam Gears



HKS Power FC with hand controller



New Nissan injector seal kit with new Pintle caps (installed less than 300kms ago)



HKS electronic boost controller



3.5” catback exhaust with 4” oval rear muffler (nice and quiet)



RDA slotted and dimpled rotors with Intima SR brake pads (installed less than 1000kms ago)



Genuine Nissan Tie Rod ends (installed less than 1000kms ago)



Rebuilt Drive shafts with new CV boots (installed less than 1000kms ago)



Steering Rack boots (installed less than 1000kms ago)



Rebuilt Headlight Switch (installed less than 1000kms ago)



Wheel alignment performed by Capital Steering less than 500kms ago



Will come with standard ECU, used Z32 AFMs , standard castor rods, rear camber arms and a spare drivers side window




IMG_3751_zpse1a54a49.jpg



IMG_3721_zpsbfd5df32.jpg



IMG_3722_zps079d5510.jpg



IMG_3711_zps190769a4.jpg



IMG_3694_zps412a236b.jpg



IMG_0168_zps4ec5f741.jpg




IMG_1795_zps2f2fe1ea.jpg



Link to comment
https://www.sau.com.au/forums/topic/442457-1990-r32-gtr-22000-act/
Share on other sites

  • 3 weeks later...

The pillar trims are out of the car as I am looking to replace the old ones with a new set from nissan

How much were the pillar trims? im actually looking to get a new set too - GLWS

It's a very nice one Terry.

Jimmy parked next to mine at a local Shannons gig recently.

I gave it a good look over and It looks honest to me.

I'm sure he'll will provide pics/info soon.

  • Like 1

Any rust Jimmy?

Got pics of the onside & engine bay?

Who was the importer?

Any de-reg?

I will have a look through my papers and get back to you on the import details

The car has a few small superficial surface rust patches on the undercarriage but its definitely nothing concerning or structural.

Here is a video walk around of the car including interior and also the engine bay

How much were the pillar trims? im actually looking to get a new set too - GLWS

I just bought a new set for my V-Spec 2.........

Part Numbers are as follows:

  • NI-76934-04U00
  • NI-76935-04U00

Nissan List price $159.70 ea + GST = $175.67 ea.

Cheers,

Bob.

I just bought a new set for my V-Spec 2.........

Part Numbers are as follows:

  • NI-76934-04U00
  • NI-76935-04U00

Nissan List price $159.70 ea + GST = $175.67 ea.

Cheers,

Bob.

Thanks mate!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...