Jump to content
SAU Community

Recommended Posts

****R32 gtst Gtr parts****

Rb20det complete engine great compression

Comes with all accessories $700

R32 manual conversion with heavy duty clutch $750

Genuine Gtr bonnet painted to whatever colour $600

Genuine Gtr front bar $600

Genuine Gtr front bar with genuine n1 vents $650

Genuine Gtr headlights $200 pair

Drift techs with toyo proxies r1s $1400

Bc Coilovers for r32 gtst only 1 month old $800

Blitz return flow intercooler set up $300

Adjustable rear camber arms r32 s13 a31 $120

Walbro fuel pump in a 32 cradle $100

R32 front strut brace $80

R32 massive rear strut brace $100

R32 Gaurds $70 each

R32 m spec side skirts $150

R32 m spec rear pods $100

R32 rear bar $70

R32 boot with gtst wing $80

R32 drivers indicator mint $40

R32 front Reo $90

5 stud front and rear includes calipers and slotted rotors $500

R32 mint dash no bubbles etc comes with mint vents no broken vents $300

R32 gtst cluster $50

R32 centre console $50

R32 front seats $40

R32 brake master $100

Gold Coast

0487924497

post-50709-0-33000400-1399109346_thumb.jpg

post-50709-0-92539600-1399109381_thumb.jpg

post-50709-0-45496300-1399109438_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/442650-r32-gtr-and-gtst-parts/
Share on other sites

  • 6 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...