Jump to content
SAU Community

Recommended Posts

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Rb30's need a few small modifications first eg needs oil lines tapped into the block for the turbo, I'm also not sure how strong the crank would be on an rb30 to handle 300rkw.

Machining costs mite be expensive as their is more work needed.

I'm current getting my Rb25det machined with arias forged pistons, rb26 rods and keeping the crank standard. Its costing me heaps, buy the time you but all parts and put it all back in, it becomes a motor reliable motor, and should have no probs handling the power out put your after, If tuned well. But if you have the money to put an rb30 bottom end in I would recommend it as their are good benefits. But to make the motor reliable and strong you would have to spend a lots more all round to make that happen.

Rb30's need a few small modifications first eg needs oil lines tapped into the block for the turbo, I'm also not sure how strong the crank would be on an rb30 to handle 300rkw.

Machining costs mite be expensive as their is more work needed.

That depends what RB30 block you get. SII block has all the provisions for the turbo.

Apart from that the only other modifications required depends on what cam belt you use.

Its a little off topic but just to compare how tough the RB rods are:

Here's a little snip from a bloke i'm exchanging pvt messages with.

He's got a RB26 with a GT40 thats almost done.

My brothers is running 300rwkw at the moment and is only using stock rods, and I'm pretty sure it would be able to handle 350rwkw, just excessive revs may decrease their life span dramatically.

Hopefully we will be aiming for near 400 so we will be able to work out what is going to go first in a standard (although brand new and balanced) bottom end.

Generally most workshops will start upgrading the rods once they near 400rwkw. Although PSI03L has been running shotpeened standards for a while (nearly 2 years) and that has been running in excess of 500rwhp.

Hopefully my rods handle 300rwkw maybe just a little more with no problems. :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
×
×
  • Create New...