Jump to content
SAU Community

Humming/whirring Sound Coming From Front Lh Side - Not Wheel Bearing!

Deanne124
 Share

Recommended Posts

Deanne124 Newbie

Deanne124

Posted
Posted

Hi,

Recently, I purchased a 2010 Nissan Dualis (FWD). The vehicle was being sold by a panel beater who had purchased the car as a repairable write off and carried out the repairs himself. I was aware of this right from the start and asked to see pictures of the damage. The seller showed me pictures of the damage and and it was insignificant. I made the mistake of not taking the car for a long test drive. Anyway, driving home in the vehicle after the sale was finalised I noticed a whirring/humming noise coming from the front LH side. This noise was particularly noticeable when the car was doing speeds of 75-90kms.

My Dad is mechanically minded so I took him for a drive in the car. His thoughts were that it was the front LH wheelbearing. I rang the seller who told me that both LH and RH wheelbearings had been replaced and the parts were taken from a Nissan Dualis (Stat Write Off) with only 13,000kms, so he was certain there was no problem with the wheelbearings. He asked me to get my local Nissan dealership to provide their opinion. I took the car to my local Nissan dealership and the mechanic advised that he thought the problem was the LH wheel bearings. I booked the car in and they replaced the left side wheelbearings. This did not fix the problem. My Dad has replaced the whole left side drive shaft which hasn't made any difference.

Does anybody have any ideas on what the problem could be?

I should also point out that the tyres have plenty of tread and have been switched around to make sure that they are not the problem.

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

It has bridgestones on the front and coopers on the back

Need more information than that mate.

Tyres can easily be rethreaded (bad). How old are they (look on sidewall for some codes)? Condition of tyres?

When I first got my R31, it had steering wobble at highway speeds and noise. Changed tyres + toe alignment = fixed.

scotty nm35 Grand Master

scotty nm35

Posted
Posted

Try a new set if possible, I have changed many a wheel bearing due to tyre noise.

The only other logical solution is both times the wheel bearing was pressed onto the hub by the outer shell, something I see far too often. It is ruined before it's put back on the car. I would hope Nissan didn't put the apprentice on the job...

GTR-N1 Grand Master

GTR-N1

Posted
Posted

Just a check > Before swapping tyres or rotating wheels, upon inspection the flat section that meets with the hub isn't painted is it? If so, scrape/burn it off.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      Dose's Sometimes DIY and Pay Someone Home & Boat Improvement Thread

      By Dose Pipe Sutututu · Posted

      Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • Kinkstaah
      Strange issue RB25DET wont start

      By Kinkstaah · Posted

      I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • Kinkstaah
      First time Skyline owner

      By Kinkstaah · Posted

      The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...