Jump to content
SAU Community

Recommended Posts

Hi all,

Up for grabs is a set of 4x R34 GTR wheels which measure 18x9 +30 all round, and are currently wrapped in 245/40 Advan AD08 tyres.

These wheels are not like other GTR wheels I've had before, these are in the less common colour which I am lead to believe came out in the Nur spec 34 GTRs?

Anyway, it is the set to the left which are for sale. They have the usual gutter rash on each wheel as can be seen in the photo below.

10346975_866742840008145_1794348662_n_zp

10379199_866771296671966_907735784_n_zps

Wheels will come with their centre caps.

The wheels are located in the south east suburbs of Melbourne and I would rather a local sale at this stage unless you can arrange your own postage.

I am after $1500 for the set. I'd be keen for swaps, but they must be 18s and 9" wide minimum.

Contact is best made through PM or by posting here.

Thanks,
Adam

Edited by adam-__-

Hmm now that you've posted that up, mine are definitely not that colour! Mine are more of a champagne/bronze shade.. I will post up a better quality photo of them tomorrow (today)

Perhaps Nissan made 3 colours! > Which means that yours were Nur-dedicated after all!

The ones I posted up were for Midnight Purple.

But either of the light colours would certainly suit a car with a dark body-colour.

Here's another photo taken with a proper camera!

DSC_0145_zpsa4a2429e.jpg

I guess we can't rule out the fact that it is resprayed in a custom colour altogether.

For any interested parties, the above wheel is an indicator of how the others wheels are also in terms of gutter rashes.

Hmm well there you go! I can't seem to find that article/thread where they mentioned it but it might have been just the illusion of the Nur coloured cars.

Either way, the wheels are a lighter shade and look great against my white car, compared to the usual grey.

Edited by adam-__-

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...