Jump to content
SAU Community

Recommended Posts

Hi Guys,

I had a look around and couldn't find a guide on the Attesa system so thought I would throw something together to list all the fluids and their change method.

Engine Oil

Type - 5w30 or 10w30

Info - Depending on the climate, use 5w30 if you see temperatures less than or close to 0

Amount - 5L

Automatic Transmission Fluid (ATF)

Type - JASO 1A

Info - Some people say to use MATIC J exclusively. MATIC J is just a Nissan names for JASO 1A fluid. It is available at any auto store for about $10 a liter

Amount - 10L

Power Steering Fluid

Type - JASO 1A

Info - Most cars use ATF in the power steering system, and the Stagea is no different

Amount - 1L

Attesa Fluid

Type - JASO 1A

Info - Same as the ATF. Power steering and Attesa systems are just hydraulic systems and could really use any fluid in reality

Amount - 2L

Transfer Case

Type - JASO 1A

Info - Same as the ATF

Amount - 1.5L

Front and Rear Differentials

Type - 80w90

Info - Front diff and rear diff use the same fluid.

Amount - Rear 1.8L - Front 1.5L

Brakes

Type - Dot 3 or higher

Info - You can use Dot 4 or Dot 5.X as they are newer specifications and backwards compatible. You shouldn't mix fluids, so if you are changing or unsure of current fluid, flush the system completely.

Amount - 0.5 to 1.0 L

Engine Oil Change

Step 1.

Warm up the engine. This helps the oil to drain. The task can be completed with the engine at full operating temperature or about half way. I prefer half way so the oil doesn't burn you and the oil filter is not too hot to touch.

Step 2.

With a 14mm spanner, remove the sump plug and drain the oil in to a pan capable of taking over 5 liters.

Step 3.

Clean the sump plug and inspect the brass sealing washer. If it is serviceable, install the sump plug and ensure it is tight. A 1/4 inch drive at firm pressure is all that is required to fasten the sump plug. Any tighter and you can damage the sump or plug on removal next time.

Step 4.

Remove the oil filter. This can be done by hand usually. There are also inexpenscive tools available for this which will make the job easier. The VQ25DET has a very easily accessed oil filter. When removing, have the drain pan under to catch any draining oil.

Step 5.

Clean around the oil filter sealing face. Open up your new 436 or 455 filter and smear some clean oil over the square o'ring seal. This helps you tighten the filter without it pinching or dragging. Install the oil filter as tight as possible by hand. Usually this will be 1/4 turn past where it makes first contact with the sealing faces. This doesn't have to be super tight either.

Step 6.

Pour 4.5L of oil in to the filler neck. Check the dipstick and continue to fill to the full mark. Start and run the engine at idle for a moment to circulate oil around the engine. Recheck and top up oil level if required.

Automatic Transmission Fluid

Step 1.

Warm up the engine. This helps the oil to drain. The task can be completed with the engine at full operating temperature or about half way.
Step 2.
With a 17mm spanner, remove the drain plug from the transmission pan and let the fluid drain in to a pan capable of taking over 5 liters.
Step 3.
Using the automatic transmission dipstick neck, fill the transmission pan back up with clean fluid. Approximately 4 liters.
Step 4.
Remove the return line from the automatic transmission fluid cooler. This line is located near the engine oil filter and is the lower line of the two going to the transmission fluid cooler. Point this line in to a cleaned, empty drain pan.
Step 5.
With help, have the car started while watching the colour of the fluid coming out of the transmission fluid cooler. The automatic transmission pumps fluid from the pan, in to the auto, through the stall/torque converter and then in to the cooler and from the cooler in to the transmission pan again. If the colour does not change to clean after 2L, stop the engine and top up the transmission using the dipstick neck till full again. Once the fluid leaving cooler is clear, switch off the engine and continue to fill the automatic transmission until full. If after pumping more than 5 liters the fluid has not changed colour, the existing fluid was already the same colour as the new fluid and you have drained enough to have completely flushed the system. You should not drain more than 2L at a time without refilling the transmission back up as the pan can run dry.
Step 6.
Replace the transmission cooler line and secure the hose clamp.
Step 7
Check transmission fluid level and if full start the engine and idle for 10 seconds. Recheck level and fill if required. A final check when hot will confirm correct fluid level. The car should only be driven if the fluid level hasn't changed after short periods of idling. The reason for that is due to the transmission holding over 10L of fluid. If you were to have an empty transmission and fill it with 4L of oil, the dipstick will show full but as soon as you start the engine it will be empty as the transmission has pumped it around the system.
ATTESA Fluid
Step 1.
Under the steering wheel panel there is a small tab hiding the OBD port. Once accessed, further up the wires is a small 1 wire plug. Disconnecting this plug will cause the ATTESA override. This causes the pump to run when pressure is low. This allows us to use the pump as a draining method. Unplug this small plug. Turn the key to ON
Step 2.
Remove the right rear panel and the black compartment plastic from in the boot. The black compartment plastic pulls out from the top first. This reveals the ATTESA reservoir.
Step 3.
On the transfer case is a small 10mm bleed nipple, identical to those found on brakes. It is located at the tailshaft end. Using the same method used on brake bleeding, slightly loosen this bleed nipple and have the fluid drain in to a clear hose and a clear container. The clear hose and container will help you determine when the old fluid has been flushed as there is a distinct colour change.
Step 4.
While the pump is cycling or running constantly to drain the system through the bleed nipple, watch the reservoir and ensure it is not emptied fully. The reservoir should be as low as possible without running dry. Once close to empty, switch the car off at the key.
Step 5.
Fill the reservoir to the very top (well above the max line) with clean fluid.
Step 6.
Switch the key back to ON and watch the fluid leaving the transfer case. Once it is fresh fluid, switch the key to off. Keep in mind that you don't want to run the reservoir empty so it might help to have a second person watching the reservoir. There should be no air bubbles at this stage. If there are air bubbles, continue to fill the reservoir and bleed until all air bubbles are gone.
Step 7.
Fill the reservoir to 1cm above the max line. Using the bleed nipple on the pump, turn the key to ON and drain that 1cm of excess fluid through the pump bleed nipple.
Step 8.
Tighten bleed nipples and return dust caps.
Step 9.
Final check of the fluid level and return boot compartment plastics.
Transfer Case, Front and Rear Diff Fluid
Fluid type varies between transfer case and differentials however the filling process is the same.
Step 1.
Using a 10mm hex driver, loosen the filler hole first. This is done to ensure you can get fluid back in after draining. These hex bits can be very tight and full of dirt and grit. All this adds up to a damaged plug if removal isn't done carefully. Clean the inside of the plug and ensure the hex driver is fully inserted before torquing.
Step 2.
Remove drain plug and drain fluid in to a pan
Step 3.
Clean the magnetic drain plug of the build up. Inspect the sealing washer and if serviceable re-install and tighten drain plug. A 1/4 inch drive and a firm tighten is all that is required.
Step 4.
Using a pump filler, fill the diff until it is overflowing. This should be done on level ground to set the correct fill level.
Step 5.
Inspect the sealing washer and if serviceable re-install and tighten filler plug. A 1/4 inch drive and a firm tighten is all that is required.
Edited by Jason Broadhurst
  • Like 2

Engine oil is a bit thin, I only use 5w40 or 10w40 these days. Perhaps as the engines get older they seem to like a slightly thicker oil to stop the valve train noise. Try and run synthetic and change regularly, these engines run too hot for lax servicing intervals.

For Matic J i use Nulon synthetic as a direct substitute.

The rest I totally agree with.

Power Steering Fluid

Step 1.

Remove as much fluid as possible from the reservoir. You can do this by any means.

Step 2.

Fill the reservoir with fresh fluid. The power steering system (most systems are engineered this way) has an equal amount of fluid in the reservoir as is used in the system. Step 1 and 2 have diluted the old fluid and new fluid 50:50 now.

Step 3.

Start the engine and turn the steering wheel lock to lock a few times. This will ensure all the new fluid enters the system and is mixed with old.

Step 4.

Continue to repeat steps 1 through 3 a few more time. I typically do it 4 times in total leaving 3% old fluid (approx).

Step 5.

After a short drive, check fluid level and top of if required. There should be no noise from the pump or rack. A slight buzz will be heard at full lock, this is normal.

  • Like 1

Hi Guys,

I thought I would put some information on how to change all the fluids in the car except for brakes and coolant, as it is covered elsewhere.

Engine Oil

Type - 5w30 or 10w30

Info - Depending on the climate, use 5w30 if you see temperatures less than or close to zero. Consider 10w40 if your engine is higher km

Amount - 5L

Filter - 436 or 455

Automatic Transmission Fluid (ATF)

Type - JASO 1A

Info - Some people say to use MATIC J exclusively. MATIC J is just a Nissan names for JASO 1A fluid. Compatible fluids will list JASO 1A standard on the back. It is available at any auto store for about $10 a liter

Amount - 10L

Power Steering Fluid

Type - JASO 1A

Info - Most cars use ATF in the power steering system, and the Stagea is no different

Amount - 1L

Attesa Fluid

Type - JASO 1A

Info - Same as the ATF. Power steering and Attesa systems are just hydraulic systems and could really use any fluid in reality

Amount - 2L

Transfer Case

Type - JASO 1A

Info - Same as the ATF

Amount - 1.5L

Front and Rear Differentials

Type - 80w90

Info - Front diff and rear diff use the same fluid.

Amount - Rear 1.8L - Front 1.5L

Brakes

Type - Dot 3 or higher

Info - You can use Dot 4 or Dot 5.X as they are newer specifications and backwards compatible. You shouldn't mix fluids, so if you are changing or unsure of current fluid, flush the system completely.

Amount - 0.5 to 1.0 L

Engine Oil Change

Step 1.

Warm up the engine. This helps the oil to drain. The task can be completed with the engine at full operating temperature or about half way. I prefer half way so the oil doesn't burn you and the oil filter is not too hot to touch.

Step 2.

With a 14mm spanner, remove the sump plug and drain the oil in to a pan capable of taking over 5 liters.

Step 3.

Clean the sump plug and inspect the brass sealing washer. If it is serviceable, install the sump plug and ensure it is tight. A 1/4 inch drive at firm pressure is all that is required to fasten the sump plug. Any tighter and you can damage the sump or plug on removal next time.

Step 4.

Remove the oil filter. This can be done by hand usually. There are also inexpenscive tools available for this which will make the job easier. The VQ25DET has a very easily accessed oil filter. When removing, have the drain pan under to catch any draining oil.

Step 5.

Clean around the oil filter sealing face. Open up your new 436 or 455 filter and smear some clean oil over the square o'ring seal. This helps you tighten the filter without it pinching or dragging. Install the oil filter as tight as possible by hand. Usually this will be 1/4 turn past where it makes first contact with the sealing faces. This doesn't have to be super tight either.

Step 6.

Pour 4.5L of oil in to the filler neck. Check the dipstick and continue to fill to the full mark. Start and run the engine at idle for a moment to circulate oil around the engine. Recheck and top up oil level if required.

Automatic Transmission Fluid

Step 1.

Warm up the engine. This helps the oil to drain. The task can be completed with the engine at full operating temperature or about half way.
Step 2.
With a 17mm spanner, remove the drain plug from the transmission pan and let the fluid drain in to a pan capable of taking over 5 liters.
ATF-Drain-Plug.jpg
Step 3.
Using the automatic transmission dipstick neck, fill the transmission pan back up with clean fluid. Approximately 4 liters.
Step 4.
Remove the return line from the automatic transmission fluid cooler. This line is located near the engine oil filter and is the lower line of the two going to the transmission fluid cooler. Point this line in to a cleaned, empty drain pan.
ATF-Drain-Line.jpg
Step 5.
With help, have the car started while watching the colour of the fluid coming out of the transmission fluid cooler. The automatic transmission pumps fluid from the pan, in to the auto, through the stall/torque converter and then in to the cooler and from the cooler in to the transmission pan again. If the colour does not change to clean after 2L, stop the engine and top up the transmission using the dipstick neck till full again. Once the fluid leaving cooler is clean, switch off the engine and continue to fill the automatic transmission until full. If after pumping more than 5 liters the fluid has not changed colour, the existing fluid was already the same colour as the new fluid and you have drained enough to have completely flushed the system. You should not drain more than 2L at a time without refilling the transmission back up as the pan can run dry.
Step 6.
Replace the transmission cooler line and secure the hose clamp.
Step 7
Check transmission fluid level and if full start the engine and idle for 10 seconds. Recheck level and fill if required. A final check when hot will confirm correct fluid level. The car should only be driven if the fluid level hasn't changed after short periods of idling. The reason for that is due to the transmission holding over 10L of fluid. If you were to have an empty transmission and fill it with 4L of oil, the dipstick will show full but as soon as you start the engine it will be empty as the transmission has pumped it around the system.
ATTESA Fluid
Step 1.
Under the steering wheel panel there is a small tab hiding the OBD port. Once accessed, further up the wires is a small 1 wire plug. Disconnecting this plug will cause the ATTESA override. This causes the pump to run when pressure is low. This allows us to use the pump as a draining method. Unplug this small plug. Turn the key to ON

ATTESA-Wire.jpg

Step 2.

Remove the right rear panel and the black compartment plastic from in the boot. The black compartment plastic pulls out from the top first. This reveals the ATTESA reservoir.
ATTESA-Reservoir.jpg
Step 3.
On the transfer case is a small 10mm bleed nipple, identical to those found on brakes. It is located at the tailshaft end. Using the same method used on brake bleeding, slightly loosen this bleed nipple and have the fluid drain in to a clear hose and a clear container. The clear hose and container will help you determine when the old fluid has been flushed as there is a distinct colour change.
ATTESA-Transfer-Case-Bleed.jpg
Step 4.
While the pump is cycling or running constantly to drain the system through the bleed nipple, watch the reservoir and ensure it is not emptied fully. The reservoir should be as low as possible without running dry. Once close to empty, switch the car off at the key.
Step 5.
Fill the reservoir to the very top (well above the max line) with clean fluid.
Step 6.
Switch the key back to ON and watch the fluid leaving the transfer case. Once it is fresh fluid, switch the key to off. Keep in mind that you don't want to run the reservoir empty so it might help to have a second person watching the reservoir. There should be no air bubbles at this stage. If there are air bubbles, continue to fill the reservoir and bleed until all air bubbles are gone.
Step 7.
Fill the reservoir to 1cm above the max line. Using the bleed nipple on the pump, turn the key to ON and drain that 1cm of excess fluid through the pump bleed nipple.
ATTESA-Pump-Bleed.jpg
Step 8.
Tighten bleed nipples and return dust caps.
Step 9.
Final check of the fluid level and return boot compartment plastics.
Transfer Case, Front and Rear Diff Fluid
Fluid type varies between transfer case and differentials however the filling process is the same.
Step 1.
Using a 10mm hex driver, loosen the filler hole first. This is done to ensure you can get fluid back in after draining. These hex bits can be very tight and full of dirt and grit. All this adds up to a damaged plug if removal isn't done carefully. Clean the inside of the plug and ensure the hex driver is fully inserted before torquing.
Step 2.
Remove drain plug and drain fluid in to a pan
Step 3.
Clean the magnetic drain plug of the build up. Inspect the sealing washer and if serviceable re-install and tighten drain plug. A 1/4 inch drive and a firm tighten is all that is required.
Step 4.
Using a pump filler, fill the diff until it is overflowing. This should be done on level ground to set the correct fill level.
Step 5.

Inspect the sealing washer and if serviceable re-install and tighten filler plug. A 1/4 inch drive and a firm tighten is all that is required.

Front Differential filler and drain points

Front-Diff.jpg
Rear Differential filler and drain points
Rear-Diff.jpg
Transfer Case filler and drain points
Transfer-Case.jpg

Power Steering Fluid

Step 1.

Remove as much fluid as possible from the reservoir. You can do this by any means.

Step 2.

Fill the reservoir with fresh fluid. The power steering system (most systems are engineered this way) has an equal amount of fluid in the reservoir as is used in the system. Step 1 and 2 have diluted the old fluid and new fluid 50:50 now.

Step 3.

Start the engine and turn the steering wheel lock to lock a few times. This will ensure all the new fluid enters the system and is mixed with old.

Step 4.

Continue to repeat steps 1 through 3 a few more time. I typically do it 4 times in total leaving 3% old fluid (approx).

Step 5.

After a short drive, check fluid level and top of if required. There should be no noise from the pump or rack. A slight buzz will be heard at full lock, this is normal.

Edited by Jason Broadhurst
  • Like 1

So if someone can chuck that post above in to the top post, and remove brakes from the title that would be great.

Also if anyone has some detailed photos or diagrams I could use, just let me know.

Enjoy.

I just wanted to say I love you. :wub: I've done the engine oil in my PNM35 but the tranny and diff oil changes have had me a bit worried, thanks for the guide.

Nice write up Jason. If you feel up to it, can you post it on M35Stagea.info? That's a better place to store good info IMO. I can copy/paste it if you don't want to & don't mind.

Cheers, Leon.

  • Like 1

Great write up! I was just contemplating a trans fluid change too. Thanks for the info.

Have you done a shift kit on your car yet? If not its the best time to do it. If you dont actually remove the pan and valve bodies you will only be changing about half the oil. Plus its probably the single best mod you can do to an m35

  • Like 2

Tell me more brick :)

Search m35 shift kit. There are many many feeds about it on here. #@Jetwreck is your man for supply and possible fit depending on your location.

Basically it is an upgrade to the valve bodies of your transmission, it makes for faster shifts and less power loss between gears. Also it can help prolong the life of gearbox.

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...