Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

40bucks to smoke up the tyres - bargain! and yeh the skylines are a challenge to get arodund some of the courses. but that just makes it more fun. i cannot wait for the next one. ill promise to produce more smoke at the next one hehe

duncan can you dub me a copy of the footage asap?

i cant make it over on the weekend (family shit before going away)

could i pick up a copy tonight?

nup, I wont get a chance to do this until later this week or weekend!

but give me an address and I'll post it to you, hope they run vhs wherever you're off to

Neil I thought you wanted to remove the lock and weld the door shut anyway :thumbsup:

Neil I thought you wanted to remove the lock and weld the door shut anyway ;)

Only on the rears and hatch buddy. Don't laugh,,, welding up the doors is apparently what they used to do in sports sedans in the old days. Hows about I chock the doors, remove the hinges as well and then weld the door on.

So when do I get to see the vid buddy???. I need to see the ulsar lifting her rears.

Neil.

the results are out!

ok here's the skylines club boys and girl:

Class B

Nick - Toyota MR2 - 22nd place with 344.27 points overall

Neil - Nissan Pulsar - 24th place with 349.25 points overall

Class C

Tosh - Datsun 200B - 29th place with 403.73 points overall

Class D

Chris - Nissan HR31 - 25th place with 353.21 points overall

Mark - Nissan R31 - 26th place with 354.16 points overall

Class DE

Kelly - Nissan 350Z -28th place with 361.8 points overall

a good result in the end. can't wait for the next one!

cheers, MARK

Yea but you 2 picked on the poor old ulsar and now I can't open the n/s/f door you pair of bastards. More bloody work.

Neil.

Dont be looking at me, I did however laugh while watching your front gaurd flex under the power of the 200b ;)




  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...