Jump to content
SAU Community

Recommended Posts

I will be emailing kelford later today, thanks for the info.

And sorry I pissed off lithium that much... Lots of info, thanks guys! Bottom line is we can't really compare any camshaft from different brand because they are all measured differently.

I will be emailing kelford later today, thanks for the info.

And sorry I pissed off lithium that much... Lots of info, thanks guys! Bottom line is we can't really compare any camshaft from different brand because they are all measured differently.

Well no, they are all measured the same, you just have to know how to read the cam card

Cams aren't really that hard and people way over think them, IMO you choose a cam to suit the application/intended use of the engine

You also can not choose a cam for turbo because it worked in a NA, they are two different animals and need to be designed and built that way, simple explanation is NA needs air velocity turbos need air volume, that is the simplest explanation and as much as I can go a lot deeper in to this this thread is about cams, not head design intake designs exhaust design etc etc

  • Like 1

They quote 50 thou and 1mm. They are different values. They know what they are doing ;)

Yes you are right. I was looking at the valve lift curve which has them marked as the same thing. But the tables to the left show them separately. For these cams there are 4 degrees difference between the durations at 1mm and at 50 thou.

26_a_in_260_915_ex_252_915_32_33_e.pdf

26_b_260_915_32_33_e.pdf

RB26DETT_256-925_3233_e.pdf

You also can not choose a cam for turbo because it worked in a NA, they are two different animals and need to be designed and built that way, simple explanation is NA needs air velocity turbos need air volume, that is the simplest explanation and as much as I can go a lot deeper in to this this thread is about cams, not head design intake designs exhaust design etc etc

If you have a 1:1 ratio of exhaust manifold back pressure to boost pressure (or better) choosing an NA cam is a good place to start!

If you have a 1:1 ratio of exhaust manifold back pressure to boost pressure (or better) choosing an NA cam is a good place to start!

True.....but when you say NA cam what you really mean is standard, OEM spec NA cam. Not a hot NA cam.

True.....but when you say NA cam what you really mean is standard, OEM spec NA cam. Not a hot NA cam.

I mean a hot NA cam... big duration and lift.

I'm not sure I follow you. In order to minimise reversion of hot exhaust gas into the cylinder you want to keep total duration under control and you certainly want to minimise overlap - compared to what you would do for an NA engine. Are you sure you don't mean the exact opposite of what you said?

Cam talk rules. Can go on forever and get nowhere fast.

The one difference with double overhead cams is that overlap can be adjusted. So perhaps an aggressive na cam can be dialled back in to something more sensible with the turbo.

Cams are, more than most things, an exercise in matching lift/duration to all the other stuff you have going on (rev range, turbo, CR, etc etc etc). A 272 may be an absolute weapon on an RB30/26 but hopeless on a 26. I don't know I haven't tried one. My limited experience was to go from Poncam B's to a 256/252 combination on a 26. Car made less power on an extra pound boost but was quicker. The biggest difference was in the low to mid range. So based on that extrapolating to 272 I cant reconcile it with what I had.

Longer duration move your torque up the rpm range, which is more power. Careful cam selection can get you a wider torque curve which is what everyone is chasing.

The caveat was just to remind people that duration is measured at a small amount of lift. How much lift affects how much duration. Something to be mind full of so everything is apples and apples.

Ultimately if shorter duration made more horsepower you would keep stock cams.

What was the lift and love centres on the 256/252 cams, also did you check cam/bucket clearnces

on mine both sets of cams where setup on the dyno to give best response and most linear power graph as possible, not just dropped in and that'll do

If the stock cams had more lift I would have found a set to replace the Poncams, I may have found a lobe which [email protected], if this can be scaled down to a 32mm base and fitted to an RB stick it will be :thumbsup:

I'm not sure I follow you. In order to minimise reversion of hot exhaust gas into the cylinder you want to keep total duration under control and you certainly want to minimise overlap - compared to what you would do for an NA engine. Are you sure you don't mean the exact opposite of what you said?

I am very sure, PM me if you like.

When boost pressure is higher than exhaust manifold back pressure (very few other than flat out race engines get this right) then you want overlap.

I am very sure, PM me if you like.

When boost pressure is higher than exhaust manifold back pressure (very few other than flat out race engines get this right) then you want overlap.

Ahhh, but now I see what you mean by "or better". You mean less ex manifold pressure than boost pressure. You see, seeing as that is relevant to approximately zero percent of us, I assumed you mean the other way around.

Continue on as you were!

So you have a result of a race engine which has less exhaust manifold pressure the boost pressure cause that is something I would like to see proof of, ie a data log

Higher duration cams on any turbo application is not the best way of building them unless you want it to rev it to the moon which defeats the purpose of turbo charging

Duration is the working range of your engine, different turbos can blur this and unfortunately good is the enemy of better

this is a theory I have had since I first started building turbos engines back in the 90s and was proven to me when we turbo charged a mates 20v R1 and I have the reason why but I'm gonna let you try and figure it out for your selves

So you have a result of a race engine which has less exhaust manifold pressure the boost pressure cause that is something I would like to see proof of, ie a data log

When I get to it I will measure it not to prove it to anyone but having higher boost than manifold pressure is what I want to achieve and I won't know without measuring.

overlap will depend on your static comp ratio.

no point in having huge overlap unless you have 11:1 comp or something crazy.

its all about matching everything to where you want the power to be made.

either way

lots of lift is good on these motors

btw lots is a relative term.

unless someone with more money than I can develop an aftermarket head for rbs with raised ports larger cam journals that are raised and bigger diameter lifters.

so we can see what .600+ thou lift does

I've pesonnaly never seen it happen and can't imagine it's possible and I have been involved in a few turbo charged race car builds, the only way to lower manifold pressure is bigger exhaust housing and bigger turbine wheel, both of which induce lag, the turbine would need to be bigger then the comp wheel for starters

Then add to that you want to use high duration cams, I hope your happy to rev this thing past 10k chase my guess is your going to have to

The only reaso you use high duration cams is if you want to increase your high range

I've pesonnaly never seen it happen and can't imagine it's possible and I have been involved in a few turbo charged race car builds, the only way to lower manifold pressure is bigger exhaust housing and bigger turbine wheel, both of which induce lag, the turbine would need to be bigger then the comp wheel for starters

Then add to that you want to use high duration cams, I hope your happy to rev this thing past 10k chase my guess is your going to have to

The only reaso you use high duration cams is if you want to increase your high range

What can be considered as high duration ? Is it dependant on the engine make or theres some sort of concensus ?

You went with TYPE-R, if you could, wouldn't you have prefered if it came with a higher lift ? like 10.25 ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...