Jump to content
SAU Community

Recommended Posts

First I'm going to start with restoring your headlights with toothpaste.
I'm guessing most people know about this but if you don't it's going to cost you 50c rather than a $30 headlight restoration kit from an auto shop.
If you have an old imported vehicle from japan it's most likely going to have yellow headlights. This is how you can make them brand new for next to no money.
1. Clean headlights with water and a clean rag.
2. Apply whole headlights with toothpaste
3. With rag scrub the tooth paste into the headlight trying to remove as much of the oxidation as possible
4. Clean tooth paste off with water and wipe dry
You can do this again to get them more clear if they are still a little yellow but it should work first time and look brand new!
tip - Clean one headlight first to see the difference and you'll be amazed.

(More post's to come later)

Ask to see room at hotel, steal toothbrush kit from bathroom while viewing room, then tell them u don't like 'the vibe' of the room and don't check in. Raid salvo's bin and nab old t shirt. Result, free tools for headlight mod.

But agreed, thread title could be 'broke-ass mods' or similar. Anyway, 2 faves are, plug up bypass hole in base of bov for more responsive throttle, and 3in pipe into rubber intake mods. Cheap n good.

  • Like 1

Nothings going yo make your na cat actually go better for free.

So, i actually reccomend a semi thought out hole in airbox will make some more induction noise and is free. Will suck hot air but won't matter. Will sound slightly better.

Not sure if na skylines have a resonance chamber type thing on their inlet, probably do. If so get rid of it. Car will sound better.

I cut a big slot on my R31's airbox, makes a barely audible purring noise when you close the throttle. Also makes the air filter dirtier quicker. Apart from that, no difference. In fact, complete airbox + snorkel apparently gives you slightly better fuel economy. LOL

Check tyre pressures.

I've been guilty of driving with lower than optimum pressures especially if the car sits for months at a time.

Yes! Me too. I was going to suggest buying a hand-held pressure gauge but that would make it not 'free'. :)

Take a big shit before a drive. Weight reduction ftw.

Also, diet. Save money on food AND go faster.

I've done this personally :)

Lost 20 kilos so I'm no longer a fat shit. Better power/weight ratio, fuel economy & health lol :P

But also taking out all the crap/junk that's in your car all adds up too for whatever little weight benefit it provides. At least you'll have a clean car for sexing the ladies ;)

This thread is going to provide some good laughs by the looks of it. My suggestion was what Hadouken beat me to, take off your CAT, bash it out, bolt back on. You get killa pop on the downshift sometimes and who doesnt want that?

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...