Jump to content
SAU Community

Recommended Posts

So not that any of this applies to me; but to avoid these two problems:

- Cop defect for exhaust too loud

- EPA road side defect/cop defect for de-cat exhaust system

Could one not instal a hidden kill switch in their car, and hit the switch, pretending the car doesn't turn on for whatever reason, therefore not allowing the EPA/Cop to check the loudness or more importantly, if it is venting toxic fumes due to decat. At least temporarily, and then tow the car home n change it back to stock?

This example referrs to if you're driving and pulled over "randomly" and then directed to an EPA station from there directly. Or more likely, the cop with a decible meter.

I wouldn't recomend this idea, just wondering if this is a possibility.

Link to comment
https://www.sau.com.au/forums/topic/451623-epa-exhaust-defect-kill-switch/
Share on other sites

Must easier just to get a well made exhaust. Running a decat is for the sort of people that throw rubbish out the window, ie, dirtbags. IMO they give the community a bad name.

And yeah they'll just write you a defect anyway. They can still write a defect if the car is not defective, they just have to suspect its defective (or if you fail the idiot test they'll write you one up to f**k with you).

  • Like 1

yeah fair enough, been defected before when the car wasn't even too low.

the real question here though is, i've heard at times, they make you drive to a carpark or something straight away and there are EPA testing stations, testing your exhaust for toxic gases. hypothetically, a car not starting would cause for it to not be tested?

They dont need to touch your car, they only need to suspect it to defect you.

We had a EPA noise test letter sent to us, was issued the day the car had a roadworthy and was inspected at Vic roads for rego.

5 coppers (young red necks) were standing on a corner in the city the first night we went out, cars exhaust was super quite, car was driven gently through traffic, one of them noted the plates and made a report.

Just because it was a Skyline and shinier than the shitbox they probably drove.......

About police looking at the car, disconnect the bonnet release or put the lever elsewhere, they can still defect you for it, but cannot open it to photograph or note the mods.

Then deal with a freindly RWC tester to clear it. (bad luck if you dont know one)

Yeah, the defect is bound to happen I guess.

my question again though, the possibility of the infamous "$10,000" fine for running a decat car can only technically be had if they can prove it is decat. the only way for this is if they nab you there and then on the road by suprise, and try and test the emissions in a carpark (as they do sometimes) this car park has random RTA n EPA officers sitting around n they pretty much test it there n then.

So in considering that, would a kill switch be a viable option to not have that happen? or will they seize the car or something i dunno lol

I seriously doubt anyone would be reading this then taking it upon themselves to investigate if someone's breaking the law.

Otherwise defects would be getting posted out to virtually everyone on here!

  • Like 1

Yeah, the defect is bound to happen I guess.

my question again though, the possibility of the infamous "$10,000" fine for running a decat car can only technically be had if they can prove it is decat. the only way for this is if they nab you there and then on the road by suprise, and try and test the emissions in a carpark (as they do sometimes) this car park has random RTA n EPA officers sitting around n they pretty much test it there n then.

So in considering that, would a kill switch be a viable option to not have that happen? or will they seize the car or something i dunno lol

Take step back. You choices are;

1. Get a nice highflow cat and get on with your life

2. Get a killswitch and know that you will still cop a defect, and may potentially get an EPA fine, and will have deal with a lot of heat if you ever have to use it.

You brain seems stuck on the killswitch idea, and you need to let that go. As far as ideas go, its a loser.

in reality though hop... why run a decat on the street. there is no benefit and its one of those defects which is probably warranted.

also general rule of thumb, be a knob to an officer and your gonna make it worse for yourself.


EDIT, beaten to it

Edited by GH05T

yeah fair enough, been defected before when the car wasn't even too low.

the real question here though is, i've heard at times, they make you drive to a carpark or something straight away and there are EPA testing stations, testing your exhaust for toxic gases. hypothetically, a car not starting would cause for it to not be tested?

So you just get a notice to come for inspection at a later time.

There is NO way out of it, stop looking for one, it doesn't exist.

The closest you can get to a decat without being caught by police is run a cat shell over a straight pipe so it looks exactly like a real cat, when they look under there is a cat there.

If called in for real polution testing, you usually have 7 or so days to present the car to bolt the stock one on.

Obviously you need the flanges of the decat one to match the exhaust flanges so its a straight swap over before you go in for the test.

Most EPA tests are just a noise based test, the serious one is the full pollution test. (anal examination)

An EPA notice is not a defect and vice versa...they are separate things and require different actions to clear.

There is a power benefit to a catless setup, even over a high flow cat and I have the dyno sheets to prove it. Is it worth it on the street? That's for you to decide. If you're on petrol I wouldn't bother simply cause the extra soot on the back of the car is a pain in the ass to clean off. If you're on ethanol this is not a problem.

kids these days..

200CPI metal cat + decent flowing but not too loud exhaust + good attitude = ZERO harrassment from cops. the attitude part is important. run a bit more boost to compensate for the exhaust losses, and get on with your life.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...