Jump to content
SAU Community

Recommended Posts

so ive had this problem for quite some time now, the sound comes and goes while driving at random except for the first couple minutes on a cold start, so far i've replaced coil packs, spark plugs, serviced injectors, these have all helped the car run a bit better but the problem is still lingering around, help?

Link to comment
https://www.sau.com.au/forums/topic/452256-rb20-r32-still-sounding-like-a-wrx/
Share on other sites

Compression test first. Identify variances across the cylinders.

You may pinpoint it down to one cylinder. If it's 2 with a low reading could be head gasket

Leak down test will further Identify in more detail the specific issue in the cylinder/cylinders

Head, rings, valves. Depends where the air is escaping. Exhaust, PCV or head.

The % low reading may also indicate valves.

Id let someone who knows what their doing. Can be time consuming.

It costs a bit more and takes a bit longer. Some shops will avoid like the plague as they don't know what they're doing or don't have the tools/experience.

Many on here can do it tho.

Edit: Where I've heard the WRX sound has normally been a single cylinder not firing.

Edited by Sinista32

Older R32 ignitors are prone to cause problems when they get hot. If you find the problem goes away after the engine has had a chance to cool a bit, then that will tend to confirm the ignitor as the culprit.

actually now you mention it, when cold started it does run fine until the engine starts warming up and on cold nights the sound does come and go much more often than during the day, should i take it somewhere to get compression tested first or just chance it on it being the ignitor module and buy a new one?

Cheapest you will find http://www.kudosmotorsports.com/catalog/genuine-nissan-pitwork-transistor-ignition-unit-ptu-nissan-skyline-r32-gtr-gts-gts25-gts4-gtst-r33-gtr-p-717.html

$500

Just get a mate to come around with one and spend 5 minutes swapping it over. Take your car for a 30 minute run

If it doesn't play up order one

These Skylines all use the same R32 GTR / GTS / GTS25 / GTS-4 / GTS-t & R33 GTR

Speak with Andrew at Kudos as there is a cheaper alternative as well

http://www.kudosmotorsports.com/catalog/genuine-nissan-pitwork-transistor-ignition-unit-ptu-nissan-300zx-z32-091993-skyline-r33-gts4-gts25-gtst-series-rb25de-rb25det-p-1298.html

needs a little bit of a change in the wiring but is more reliable/long lasting

$330

Edited by Sinista32

mine got worse when hot.. head was warped.
leakdown test will rule out allot but yes you have one cylder failing.
take out the new plugs and see which one looks different.
have you done a compression test?

To hard to be certain with a single cylinder

If you had 2 side by side with low compression most likely.

With a single cylinder could be valves or rings.

To me it sounds more likely one piston is not firing.

Get onto checking the ignitor and doing the compression test

ill get those two things done for now, also i dont know if this will help but on a cold start while idling it backfires every couple of seconds, nothing big no smoke or flames just a small backfire every second or two, the order is also random its not like it backfires every second consistently one second it might do it twice, not do it for another few seconds etc

A car backfires because unburned fuel is getting to the muffler

A backfire can be caused by incorrect timing of the spark (ignitor) or bad Tune as it's a balance of Air and Fuel

Leaking gaskets, seals, rings as this keeps the gasses in and the air out

Edited by Sinista32

*sigh* so much shit i have to fix to just find out what the real problem is, would it be a better option to just go compression test it and put it on a dyno to see exactly what the problem is, or at least narrow it down by a fair bit?

dyno will just tell you it is underpowered.

Compression test a definite to check health of cylinders - but does not tell you about spark

Ignitor first - as easiest to check and I believe you have already said you've done the plugs, coilpacks, loom etc...

Need to make sure you have spark to each cylinder.

As ghost said if you pull your plugs you will see that one is not like the others. That's the likely culprit causing the WRX sound and backfire.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did you panel beat the dents or have you tried to repair this only using filler?  Is your sanding block soft/flexible and is following the shape of the panel rather then just knocking down the high points? 
    • I haven't knocked them down yet. I think I made the repair more complex than it should have been. I had rock chips combined with waviness and dents and I tackled it all in one because it was near each other and just end up wasting a bunch of bog lol. I'll knock down those areas and see how I go. And yep what you are saying at the end is correct. I think I might be sanding the top of a steep hill then my sanding block falls into the dent and gets rid of the guidecoat if that makes sense. Though shouldnt unless I'm covering too big of an area with not a long enough block. I'll try something new and provide some updates. Getting there though! Thanks as always.  
    • Yeah makes sense, hard to comment on your situation without seeing what your doing. I was talking generally before, I would not be looking to randomly create low spots with a hammer to then have to fill them.  It's hard without seeing what your doing, it sounds like you are using the guide coat to identify low spots, as you're saying the panel is still wavy. I don't see how you're not ending up with patches of guide coat remaining in a wavy panel? Once the high spots are knocked down to the correct level, surely to have a wavy panel you need low spots. And those low spots would have guide coat still in them?
    • So I'll put filler past the repair area a bit to make sure I don't miss anything. Then I'll block it until it's almost level, put the guidecoat, then keep blocking until it's gone. Then it's still wavy.  In regards to hitting the panel, I saw this video might give more context - Skip to 0:47 he knocks it down. But yeah I'm sanding until the guidecoat is gone then checking because otherwise my filler is still well above the bodyline. Unless what you're saying is I should put guidecoat around it early, surrounding the filler then stip once it's gone?
    • I refreshed the OEM injectors with the kit and connected it up. It now ideals okay even with the IACV removed. Driving still has the same cutoff issue like the 550cc injectors so the issue is somewhere else. I bought FPG's Fuel Pump Hanger. I will be installing it next, but it is not as straightforward as I thought it was with my limited wiring knowledge and no instruction on the specific model I purchased (FPG-089). I also got the incorrect billet clamp as I could not find info on the OEM sizing.
×
×
  • Create New...