Jump to content
SAU Community

Recommended Posts

E85. I thought it would of made more but oh well have to ask Trent why it couldn't. It is a unopened 170k s1 engine. I'm thinking I should of went with the sat45 turbo now.

The boost curve is what surprises me because my other ss2 internal gate is full 21psi boost by 3750rpm and the curve looks a lot better than that and then goes completely flat.

post-84279-14333240028034_thumb.jpg

I'd replace the gasket between the runners and the plenumn. Some S1 are metal, later ones are rubber. Mines an S2 and was rubber, it started leaking and we didnt pick it up for a long time.

I used a cometic gasket from kudos ms.

Did u end up getting a front splitter made up?

im looking for ideas, want to make one soon.

Hey mate nah not yet but it will be getting sent back in to get one made up at havoc fab. Looking at something like this.post-84279-14343233710606_thumb.jpg

Yeh I looked through his build thread and found it there. Also speaking to top stage composites atm as well and might just bite the bullet and get there v3 package since tax times coming up.

  • 2 weeks later...

post-84279-14353199119936_thumb.jpg

post-84279-14353199777109_thumb.jpg

New wheels finally fitted. Had to raise the rear 50mm so they could fit. ROH Modena 18x10 +15 with 295 semis. Next I will have get the arches flared out because they sit a bit outside the guard. Don't no if I should keep them white or get them sprayed black.

Haha yeh I think some over fenders will have to be used. My panel beater is gunn try pump the guards out as much as he can first. They sit about 30mm outside the guards. As for ride height I will be coming down just have to wait until the guard are flared as the rear guard sits on the tyre if a go any lower. Haven't really had a chance to play around with my bc cooler era yet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...