Jump to content
SAU Community

Putting In New Spark Plugs. Ngk? Gap To What?

glaze

By glaze,
in General Maintenance

 Share

Recommended Posts

jiffo Mentor

jiffo

Posted
Posted

Difficult to offer correct advice unless you supply full engine details.

Generally speaking, you should run the max gap possible and for a stock engine with decent coil packs that's 1.1mm.

Likewise heat range would be 5 or 6 for a standard engine.

Once power is increased, you may find ageing coil packs can't keep up with the increased combustion pressures and the easy fix is to reduce plug gap.

Wouldn't suggest less than 0.8mm. If it takes a really close plug gap to avoid blowing out the spark you should be looking to new coil packs.

Heat range usually alters a range per 100hp increase over stock and it's pretty easy to have a 200hp increase.

Cold starts could become an issue with very high heat range plugs.

Make sure your IGN timing is correct while you're at it.

  • Like 1
jiffo Mentor

jiffo

Posted
Posted

For that hp GTR-Joey is on the money, but with your new coil packs I'd go for 1.0mm and see how she performs.

Check the shop actually sells you the BCPR plugs.

Often they'll offer BKR which is the same plug but built to ISO standards and protrudes 2.5mm shorter.

With them you need to give the spring conductor on the coil pack a bit of a tug to ensure it reaches the tip of the plug.

Grab some nickel thread anti-seize and apply a match head dob to the thread of each plug.

Tighten the plugs to the correct torque. Too loose and you'll see carbon up the threads of your old plugs. (the most common cause for stripping plug threads in alloy heads)

Blow the valley area clean with compressed air before you start removing things.

Remove/re-fit spark plugs one at a time.

So easy to drop an item down an open plug hole and suddenly that 5-minute job becomes very expensive.

  • Like 1
glaze Mentor

glaze

Posted
  • Author
Posted

Thx Boys. Luckily for me my mechanic friend will be doing the work, but will fill him in with all these tips.

Also picked up a fuel filter, wondering how easy are they to change in the R32 GTR?

  • 3 months later...
pol1on1 Mentor

pol1on1

Posted
Posted

I'm reading this topic and it's great but anti-seize

Common! !!!!

You got to think that if you putting that stuff on ya threads you start to isolate the plug from ground !!

Your coil is powering the plug but can't discharge it properly so the it searching for ground ...... Now it will find ground eventually where you did not coat the thread with. Now it can be a possibility of it electrode erode ya head meaning stripping ya threads slowly.

So not a good idea

But if you really find the need to put some lubrication on it... use graphite powder. This stuff is highly conductive and it's a dry lubricant.

Also do not use copper anti-seize coz it's reactive with alloys and normal nickel (silver ) is not good coz it's got lithium grease (non conducting)

Just my 2c

Jiffo I agree with your comment and great tips apart the Anti-seize ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      [Fuel pump] Is upgraded bulk head connectors or relay mod needed for fuel pump upgrade?

      By jtha7 · Posted

      Hi guys my 94 r33 gtst fuel pump has gone out. I have a walbro 525 ready to go in but am unsure if I need to upgrade the fuel tank bulk heads? Ive heard that others have issues with the stock wiring melting... Ive seen alot of people recommend this: https://frenchysperformancegarage.com/products/fpg-nissan-skyline-r33-r34-silvia-s14-s15-billet-fuel-tank-bulkhead-hat-top-an6-with-high-current-connector-apex-2-8-delphi-fpg-100?variant=42873255198898 My current pump that stopped working is aftermarket but I had no relay mod or upgraded connectors. Need some advice please. TIA
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      It’s new. It’s the cd009. I did take the transmission apart to mill down the bellhousing and had both housings come off the gears so wondering is something isn’t in right. I am running redline. I can get it in gear running too but it’s just not easier and it’s almost like 2, 4, 6, and reverse all the back gears aren’t happy going in
    • Nightmare_mistress_R33
      CD009 RB Conversion

      By Nightmare_mistress_R33 · Posted

      I’ll remember that as a last choice. It’s brand new
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Got keys and did a walk around the yard planning the landscaping works with the family that I will be doing Main effort: remove all the woodchip in the gardens that are around (attached) to the outside of the house and replace with 10mm blue metal, having woodchip close to the house is a recipe for inviting white ants, currently there are no white ants within the block and I would like to keep it that way I'll be buying some large raised garden beds to grow veggies and stuff, and the woodchip will be mulched with everything else that gets dug up, pulled out, or cut down during works Next will some minor drainage and landscaping maintenance up one side of the house, where the fuse box, AC, and solar stuff will go, about 12 mtrs long by 2 meters wide, I'll break up the soil, add gypsum and then I'll dig in a French drains about 300mm deep x 300mm wide and fill it with agg pipe and blue metal, then level out the whole area with a 50mm layer of blue metal, the soil, whilst currently pretty compacted, will break up well with the gypsum to aid in drainage, I'll then cover the area with a 50mm layer of more blue metal In saying this, the drainage issue is minor, but that little hidden away area down the side is untidy and weedy, and as all of the main elec stuff is there I want it neat and tidy to appease my OCD Again, the material excavated from the French drains with be added to the garden bed mulch, as will some rose bushes and some other crap looking garden plants, and a old apricot tree that is looking worse for wear The apricot tree is currently in a little roundish garden bed that is in the middle of the back yard with few other crappy looking plants around it, that will all be removed, levelled, re-turfed, and is a perfect spot for a hills hoist There is also a area about 3m x 2m between the rear fence and shed that will get some attention, it looks like some stuff was stored there and the grass is dead, that will also get broken up and mulched, and is a prime spot for a pumpkin patch I've guestimated that I'll need: 3 tonnes of blue metal, 12 meters of agg pipe, 5kg of Gypsum, and a hills hoist, so a few bags of concrete as well to set it in place (the house currently has one of those pull out 4 line jobs, whilst it works, I want a retro old school hills hoist), I am also going to run some chickens, there's a great spot for a coop, so a chicken coop to suit 4 of those lovely egg laying bitches will also be on the job card That should keep me busy for a while, and will finish off the back yard ready for a early spring planting of some veggies and berries  Once the main effort is done I'll start out the front, there's a large rock garden that could use some TLC, but that is only minor works Should be fully moved in within 2 weeks, the landscaping works will start then Fun times, retirement is good  
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      It happens, that's what your single stage filler is used for.  If it is still visible after the 3 coats of 2k primer, it will be visible after the paint is laid down.  Its hard to give 100% perfect advice without being there in person, I'm very tempted to say stop where you are, fill your pin holes with a single stage putty first then keep going. 
×
×
  • Create New...