Jump to content
SAU Community

Recommended Posts

The satin finish on the lip looks great!

I've plastidipped the chromed plated grille on my NM35, and the finish has stood up far better than I ever expected.
It gets loads of freeway kilometres, and hasn't got a single mark or stonechip in over 6 months.

  • 2 weeks later...

done f**k all on the car apart from driving it and being on holidays,
however the new leather boots finally arrived.

old ones were shagged out and even they were aftermarket.

20150120_154801_zpstjdaaame.jpg20150120_154757_zpsq1elm4nz.jpg


found out, not surprisingly that almost all of the clips have broken underneath which hold the boot on

need to track down one which hasnt been broken...... bet thats not gonna be easy.

20150224_153154_zpswc8jrztp.jpg

new boots on but with f**ked clips its just not going to sit right.

20150224_153853_zpsyrfqiois.jpg

pmed :cheers:

clutch pedal started squeaking recently, wasnt the clutch pedal bracket so checked out the gearbox side and found out there is no rubber boot on the clutch fork pivot bit.

sprayed some lube on it and it has hushed down, but where would i get a rubber boot from, looks like i can just get it on over the clutch fork without taking much apart but can you get them new anywhere?

  • 2 weeks later...
  • 2 weeks later...

still been doing f**k all apart from doing the daily shit.


did however pop down to see Paul Pavlou motors who were nice enough to find a spot of free time and popped her on the Dyno to get a base power read out.
took the opportunity to bump the boost up till the engine was happy.

to be honest i was quite surprised at the power out put but more importantly the torque output! made bucket loads. and it feels like it too. pulls like a motherf**ker for a stock car.

10psi base run - 14 psi final run.
power20vs20torque_zpsoltfs2ud.jpg


used a GFB bleed valve for now which holds the boost well, no drop or spike.

PSI20vs20power_zpshrkahhcj.jpg

now i havn't tuned anything just bumped the boost up keeping an eye on the AFR which stayed happy, nice and safe.

Power20vs20AF_zpsbumi5mme.jpg

Took it on the adelaide four six rotary cruse last night through the hills which gave me a good change to test it out properly and she pulls along nicely. also it shoots flames occasionally.... so the car behind me said :P

makes me want to get a haltech in there...


Edited by GH05T
  • Like 2

insignificant update of putting leds in the number plate lights, but jebus, how f**king dirty did these want to be.
has to use headlight polish to get through the shit.

2015-03-24%2020.37.27_zpstbcwicfw.jpg
20150322_123636_zps7sxde0xk.jpg

also it turns out the red reverse light was some super hard to get off (and quite good quality) layover wrap stuff. so thats coming off.

20150322_123704_zpsv41qiuzk.jpg

  • Like 1

also need to sort out the annoying over tensioned timing belt noise. shits me at idle.
gonna replace obviously the timing belt and associated parts

would this be the cheapest option? if you have the hookup let me know ;)
is this the preferred option?

http://justjap.com/gates-racing-timing-belt-kit-nissan-rb-twin-cam-engines.html

Should i do the water pump as well?
yeah lets do the water pump too...

should i get an N! pump while im there? i think there just a better impeller blade design yeah? not like the n1 thermostat which f**ks with street driven cars?

Edited by GH05T

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...