Jump to content
SAU Community

Recommended Posts

The satin finish on the lip looks great!

I've plastidipped the chromed plated grille on my NM35, and the finish has stood up far better than I ever expected.
It gets loads of freeway kilometres, and hasn't got a single mark or stonechip in over 6 months.

  • 2 weeks later...

done f**k all on the car apart from driving it and being on holidays,
however the new leather boots finally arrived.

old ones were shagged out and even they were aftermarket.

20150120_154801_zpstjdaaame.jpg20150120_154757_zpsq1elm4nz.jpg


found out, not surprisingly that almost all of the clips have broken underneath which hold the boot on

need to track down one which hasnt been broken...... bet thats not gonna be easy.

20150224_153154_zpswc8jrztp.jpg

new boots on but with f**ked clips its just not going to sit right.

20150224_153853_zpsyrfqiois.jpg

pmed :cheers:

clutch pedal started squeaking recently, wasnt the clutch pedal bracket so checked out the gearbox side and found out there is no rubber boot on the clutch fork pivot bit.

sprayed some lube on it and it has hushed down, but where would i get a rubber boot from, looks like i can just get it on over the clutch fork without taking much apart but can you get them new anywhere?

  • 2 weeks later...
  • 2 weeks later...

still been doing f**k all apart from doing the daily shit.


did however pop down to see Paul Pavlou motors who were nice enough to find a spot of free time and popped her on the Dyno to get a base power read out.
took the opportunity to bump the boost up till the engine was happy.

to be honest i was quite surprised at the power out put but more importantly the torque output! made bucket loads. and it feels like it too. pulls like a motherf**ker for a stock car.

10psi base run - 14 psi final run.
power20vs20torque_zpsoltfs2ud.jpg


used a GFB bleed valve for now which holds the boost well, no drop or spike.

PSI20vs20power_zpshrkahhcj.jpg

now i havn't tuned anything just bumped the boost up keeping an eye on the AFR which stayed happy, nice and safe.

Power20vs20AF_zpsbumi5mme.jpg

Took it on the adelaide four six rotary cruse last night through the hills which gave me a good change to test it out properly and she pulls along nicely. also it shoots flames occasionally.... so the car behind me said :P

makes me want to get a haltech in there...


Edited by GH05T
  • Like 2

insignificant update of putting leds in the number plate lights, but jebus, how f**king dirty did these want to be.
has to use headlight polish to get through the shit.

2015-03-24%2020.37.27_zpstbcwicfw.jpg
20150322_123636_zps7sxde0xk.jpg

also it turns out the red reverse light was some super hard to get off (and quite good quality) layover wrap stuff. so thats coming off.

20150322_123704_zpsv41qiuzk.jpg

  • Like 1

also need to sort out the annoying over tensioned timing belt noise. shits me at idle.
gonna replace obviously the timing belt and associated parts

would this be the cheapest option? if you have the hookup let me know ;)
is this the preferred option?

http://justjap.com/gates-racing-timing-belt-kit-nissan-rb-twin-cam-engines.html

Should i do the water pump as well?
yeah lets do the water pump too...

should i get an N! pump while im there? i think there just a better impeller blade design yeah? not like the n1 thermostat which f**ks with street driven cars?

Edited by GH05T

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...