Jump to content
SAU Community

Ross Harmonic Balancer.. Thoughts As To Whether This Is A Worthy Upgrade?

boobeedoobee
 Share

Recommended Posts

boobeedoobee Community Regular

boobeedoobee

Posted
Posted

Hi i am about to do the timing belt and water pump. Pretty much a major service on the car. I have bought greddy pulley kit and was wondering whether to update the old harmonic balancer. Is the ross metal jacket balancer a worthy upgrade?

boobeedoobee Community Regular

boobeedoobee

Posted
  • Author
Posted

Use the search function or f**k off, you are wasting the resource that sau is

well I have used the search button Brett.. and have found mixed thoughts and no clear answers. . Also products do change and develop. If you have nothing nice or productive to contribute why act like some tough guy over the Internet? Please refrain from further discussion on this topic as you obviously know everything right? or do I need your permission before asking a question on this forum? Seriously dude..

Trex Grand Master

Trex

Posted
Posted

He actually knows quite a lot haha. Really man I told you in your first thread just ask you question through google and type sau at the end.

If you're still struggling for a definitive answer ask here and give your reasons as to why.

I don't mind some of these threads as it broadens my mindset on modifications but some are asked over and over again and become frustrating to some members who answer these same questions over and over again.

boobeedoobee Community Regular

boobeedoobee

Posted
  • Author
Posted

He actually knows quite a lot haha. Really man I told you in your first thread just ask you question through google and type sau at the end.

If you're still struggling for a definitive answer ask here and give your reasons as to why.

I don't mind some of these threads as it broadens my mindset on modifications but some are asked over and over again and become frustrating to some members who answer these same questions over and over again.

Thanks.. I have read through the threads bur couldn't find anything definitive and most were quite old..
boobeedoobee Community Regular

boobeedoobee

Posted
  • Author
Posted

Old threads are often the better ones. You have to remember, the people who owned these cars in 06' were a lot smarter and better off than you or I. Well that's the way I look at it.

I'm not going to argue with that but.. like I've said products develop the same harmonic balancer built by ross in 06 well I dare say might have improved in 2015 .. no?

boobeedoobee Community Regular

boobeedoobee

Posted
  • Author
Posted

A Ross or ATI Balancer are definitely better than the factory one. But the question is why would you need/want to replace the factory one if it is in good condition anyway?

Thanks.. as I'm replacing every other pulley there I thought I would do the same to the balancer. As it's a 25 year old car now it makes sense. .

Shoota_77 Veteran

Shoota_77

Posted
Posted

If the rubber looks like it's starting to crack (they all have a certain amount of fine cracks) then definitely replace it. Gives you the option of going trigger kit down the track if you go with a Ross too.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...