Jump to content
SAU Community

Recommended Posts

And here's where it gets funny. Just on the offchance that he has one of those chicken lips R34s with a helical LSD, then the jack it up and spin a wheel test will not prove that it is LSD. It will instead indicate that it is not LSD, even though it really has one.

But yes, unless someone has been completely retarded, then every turbo R34 has an LSD.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/456318-r34-gtt-lsd/#findComment-7527940
Share on other sites

I always thought all R34 GT-T manuals (series 1 and 2) came with the helical torsen diff, and the auto's came with the VLSD's?

R34 GT-t S1 has a VLSD = gay

R34 GT-t S2 has a Helical = pretty damn awesome for a street car with mild power.

Link to comment
https://www.sau.com.au/forums/topic/456318-r34-gtt-lsd/#findComment-7528370
Share on other sites

This attached brochure (third last page) says the manuals were helical and the auto's viscous. That being said, perhaps the NZ imports were all specified with the helical diffs.

No. Most of the manuals are viscous too. It doesn't even seem to be true that all the S2s have a helical, from what I've seen!

R34GTT-Brochure.pdf

Link to comment
https://www.sau.com.au/forums/topic/456318-r34-gtt-lsd/#findComment-7528541
Share on other sites

I know. I used to use that brochure as the basis for my belief along the same lines. But the sad reality seems to be different. I have secondhand knowledge of only 2 R34s with helical diffs. All the R34 diffs I've followed up for my own purposes have been viscous, regardless of whether they were 4.11 or 4.08.

Link to comment
https://www.sau.com.au/forums/topic/456318-r34-gtt-lsd/#findComment-7528591
Share on other sites

Mine is a S2, pretty sure it has a helical diff in it. Built March 2001, factory manual etc

Is there any way of easily checking?

The back end sure feels better than the old viscous LSD in my 32, and hooks up as well as the 1.5 way mechanical diff I put in the 32 without the clunking around low speed corners.

You can feel the front end want to push straight if you are taking pretty constant corner and start to feed on the power, much like it did when I swapped the diff in the 32

Link to comment
https://www.sau.com.au/forums/topic/456318-r34-gtt-lsd/#findComment-7528659
Share on other sites

The brochure linked is ONLY for s2 R34's.

S2 R34's are pretty rare to begin with. They were only made for like 6 months, Late 2000 to early 2001.

99% (no idea on the number) of R34's are S1's.

I've had both diffs (well, I had a S15 diff, but its the same center...) and I actually prefer the VLSD... when it's working as the one in my car was/is in good condition (for now).

The predictability was really quite noticeably better than the Helical diff, which likes to inside spin REAL easy, which isn't really a problem at 150rwkw with good tyres, but dial it up to 400 then try and take a corner under power and then you'll find the back end being nice and unpredictable which is quite undesirable.

Link to comment
https://www.sau.com.au/forums/topic/456318-r34-gtt-lsd/#findComment-7528711
Share on other sites

I've got a r34 gtt series 2, but mine use to be a auto so the diff is a VLSD and its shit, single spinning for daysss..

I had a s15 1.5way kazz lsd i was going to fit but surprisingly its completely different. On the forum everyone says they are the same diff but NOOO..

The r34 gtt has 2 abs sensors, one on each side of the diff where the axels connect and its a short nose r200 diff housing.

The s15 has one abs sensor where the diff connects to the tail shaft hence it has a long nose housing...

SO dunno how people use s15 diffs in r34s... :verymad::verymad:

Link to comment
https://www.sau.com.au/forums/topic/456318-r34-gtt-lsd/#findComment-7528745
Share on other sites

Also my car had S15 diff, and both driveshafts.

Also it was originally a N/A, so it didn't have the traction control sensors or HICAS to remove/deal with/keep working.

It also had the ABS computer from a S15 installed into it.

(it'd be far smarter to swap the center)

Link to comment
https://www.sau.com.au/forums/topic/456318-r34-gtt-lsd/#findComment-7529430
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lamb roast on Saturday will be different 🥲
    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...