Jump to content
SAU Community

Recommended Posts

I talked them down to the original quote. The reason it was so high was because the door kyp supplied was in really bad condition (according to uneeda) he documented the repairs (as per my request, I said anything you charge me for I want to see a photo of). He claims that they spent 5 days panel beating the door just to get it to fit. The Respray is good. The colour match is perfect. Will I go back? No. The job might be good but their work ethic is crap. They should have called me and told me about all of these issues and let me decide if I wanted them to keep working on it or not. Plus they went 5 weeks over-time. 

DSC_0426.JPG

Yeah well the Original Quote was 1 Week if they could find a door. It took them 3 weeks to find a door, which I ended up finding for them, and then two weeks to get the door on the car. Now seeing how banged up the door was when they picked it up (almost looked like a different door), it makes sense... but oh well.

The way I see it is, the car is back in my hands, and fixed. Now I need to save some money, and once i'm back in my 'green' zone, I will continue to work on it.

Morning. So, now that i have my car back. I'm going to clay, cut and polish it. Starting with the hood and seeing how I go. This is really an experiment to see what results I get. The hood is covered in bird poo burn and numerous other stains, so... Let's get started 

Morning. So, now that i have my car back. I'm going to clay, cut and polish it. Starting with the hood and seeing how I go. This is really an experiment to see what results I get. The hood is covered in bird poo burn and numerous other stains, so... Let's get started 




Wish I only had to wash mine... Gotz to do a service :(

Also gotta service our suzuki :(

nah. Those are rock chips. I probably removed the stains by 50% and on the right angles they're not noticeable. But they're still there.

 

I should mention the process I used was (in this order).

 Wash --> Clay --> Cut --> Polish --> Wax, and then I sprayed some Maguires "quick detailer" on top.

It took roughly one hour, just on the Hood alone.

Edited by Manne



  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...