Jump to content
SAU Community

Recommended Posts

I talked them down to the original quote. The reason it was so high was because the door kyp supplied was in really bad condition (according to uneeda) he documented the repairs (as per my request, I said anything you charge me for I want to see a photo of). He claims that they spent 5 days panel beating the door just to get it to fit. The Respray is good. The colour match is perfect. Will I go back? No. The job might be good but their work ethic is crap. They should have called me and told me about all of these issues and let me decide if I wanted them to keep working on it or not. Plus they went 5 weeks over-time. 

DSC_0426.JPG

Yeah well the Original Quote was 1 Week if they could find a door. It took them 3 weeks to find a door, which I ended up finding for them, and then two weeks to get the door on the car. Now seeing how banged up the door was when they picked it up (almost looked like a different door), it makes sense... but oh well.

The way I see it is, the car is back in my hands, and fixed. Now I need to save some money, and once i'm back in my 'green' zone, I will continue to work on it.

Morning. So, now that i have my car back. I'm going to clay, cut and polish it. Starting with the hood and seeing how I go. This is really an experiment to see what results I get. The hood is covered in bird poo burn and numerous other stains, so... Let's get started 

Morning. So, now that i have my car back. I'm going to clay, cut and polish it. Starting with the hood and seeing how I go. This is really an experiment to see what results I get. The hood is covered in bird poo burn and numerous other stains, so... Let's get started 




Wish I only had to wash mine... Gotz to do a service :(

Also gotta service our suzuki :(

nah. Those are rock chips. I probably removed the stains by 50% and on the right angles they're not noticeable. But they're still there.

 

I should mention the process I used was (in this order).

 Wash --> Clay --> Cut --> Polish --> Wax, and then I sprayed some Maguires "quick detailer" on top.

It took roughly one hour, just on the Hood alone.

Edited by Manne



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...