Jump to content
SAU Community

Recommended Posts

Think I may have found my gremlin. Was testing fuel pressure again and had 50psi at idle, pulled vac line for reg and fuel pressure didn't change. Just ordered a nismo reg and will fit that when it gets here. This would explain why it's been so rich and fouling plugs.

I currently have the same problem with mine. Was fine on dyno this morning then on the way home developed a miss fire at 4500rpm. Gappef plugs down from .7 to .5 only lowered the miss in the rpm down to 3500. Made it worse. Going to change the plugs tomorrow. And set to .55mm.

Mine where all burning good. Tuner said hose must of fell off somewhere. Boost leak. Couldn't find any off so new set of plugs first the change fuel filter and check out the height of fuel pump in tank. After that. I'm at a loss so it will be going back to tuner if I don't find the problem

Mine where all burning good. Tuner said hose must of fell off somewhere. Boost leak. Couldn't find any off so new set of plugs first the change fuel filter and check out the height of fuel pump in tank. After that. I'm at a loss so it will be going back to tuner if I don't find the problem

Found my problem this arvo. Changed plugs didn't do anything. Pulled fuel filter out. (Aeroflow reusable one ) stainless steel screen was blocked. Changed it from 80m to 30 m took for a run and was fine. Will pull the tank on the weekend and clean it out.

Pretty sure duty cycle shouldn't be that high on 550cc squirters and 18psi on a Td06 only making 240rwkw.

Looks like the new fuel pump is required anyway

post-55653-14392828983823_thumb.jpg

Edited by fmlycar

Nah that's way too high. 550cc should be good for over 300kw on pump. Before I was having issues I would see values around 67% even with spikes of 2-3 psi in boost. Will fit new bosch pump when it arrives and report back.

Edited by fmlycar

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...