Jump to content
SAU Community

GTS-25t boot sticker.

P1E

By P1E,
in Exterior & Interior Styling

 Share

Recommended Posts

wilch Grand Master

wilch

Posted
Posted

An easy way to remove badges and stickers is to use a hairdryer... heat them up a little, then pull them off slowly. You then remove the residue with a little bit of methylated spirits, wash, then polish.

You won't be able to tell that the sticker was there in the first place unless your paint has faded noticeably (paint under the sticker will not have faded as much).

wil..

rs73 Grand Master

rs73

Posted
Posted
My R33 S1 didn't come with a sticker at the back but it came with a gold badge instead.

I guess it is not from the factory, but it gives it that little bit of prestige hehe.

Gold badge looks good on the blk line.

Coupe only got a sticker.... while 4door sedan gets the badge. Your gold one might be from the 4 door, either that or aftermarket gold one - cos on 4 door I've seen silver badge only not gold.

srb 33 Explorer

srb 33

Posted
Posted
There's a way to remove sticker without marks is to clean it afterwards and buff it out, maybe cut and polish will do.  

Have you had an experienced panel beater have a look at your car? You might be surprised how easy they can spot and point out proof of respray on things that would normally be missed by common people like us... A panel beater showed the proof on mine, I was shocked as I never paid attention on that part until he pointed some little details of previous respray job. However he praised that it is a good quality repair, so it should be ok. :rofl:

Are you saying that every R33 that doesn't have a GTS-T sticker on the back has been resprayed or had an accident. That's a huge call mate I think your jumping to a conclusion. I guess theres other reasons why;

Maybe some didn't come out with them.

Maybe owners removed them.

Maybe stickers were an option when buying?

leech_ Grand Master

leech_

Posted
Posted

i was contemplating removing mine but if people are going to jump to the conclusion it has been resprayed or accident damage i might think again. I dont see how people can just automatically assume though if the car doesnt have a sticker its a repair job ???

rs73 Grand Master

rs73

Posted
Posted
Are you saying that every R33 that doesn't have a GTS-T sticker on the back has been resprayed or had an accident. That's a huge call mate I think your jumping to a conclusion. I guess theres other reasons why;

Maybe some didn't come out with them.

Maybe owners removed them.

Maybe stickers were an option when buying?

I never concluded that way, I only ever said "could have been" resprayed, I never say that every R33 without boot sticker IS definitely 100% a respray. It suggest a possibility only. owners can remove them, but if people thinking towards respray then it is because of majority of cases are caused by respray - as people normally don't bother sourcing another sticker after respray. I don't think R33 came out of the factory without badges or boot sticker, it should be standard issue.

rs73 Grand Master

rs73

Posted
Posted

And to add to that... my car IS a respray job, and it does have stickers on.

even got the side Skyline strip which looks like an option in Japan that the resprayer even masked off, causing rough edges around the stripe sticker.

If you're in VIC and coming to any future cruises, I'll show you the respray job on my car. That is, if I haven't done another full respray on the car myself before we meet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...