Jump to content
SAU Community

Recommended Posts

Also will be dirty in 2 days, because black.

im actually getting tired of it with the gloria. sometimes its worth it. but when washing the car when its warm or even partial sunlight, its a race against time. Drying/chamois has never been so f**king time consuming AND so important. and mine isnt even daily. dunno how people do it.

found out trying photograph black cars at night in average lighting, with average camera skills is hard.

yeah i washed it the other week on a hot day.. ended up just as dirty when i began almost lol

dried up water dots everywhere, when it's clean looks goooooood though

been toying with the idea of selling one of my bikes, and convincing dad to go halfies build an old rotor, big block or similar with me.. wonder if he'd go for it. (torana, cortina, old mazda, datto 260 etc) club reg it

Edited by UNR33L

^ good move.

Dont go rotar leigh...

First rule of rotaries: know how to build a rotary.

I was reading about the different porting you can do, and blimey it was scary how they can predict the life of the engine down to the 100's of kms (mind you, not too hard when things only last a few thousand of kms)

but .. but.. they're so cool.

wouldn't mind throwing a ford xr6t engine in something too for fun, would only do if dad went halfies doe, dont have teh cash

he restored a valiant charger but sold it a few years ago, was mint :(

Edited by UNR33L

No ones discounting your polishing (pic below was pre-wax), but waxes deepen the shine; you saw the diff once it had it on there

1453064698.7595.iPicit.jpg

Didn't I give you money too lol, cheap labour

Not sure, I was happy with the whiskey. :D

but .. but.. they're so cool.

wouldn't mind throwing a ford xr6t engine in something too for fun, would only do if dad went halfies doe, dont have teh cash

he restored a valiant charger but sold it a few years ago, was mint :(

. I got one of them to restore too, rusty old bucket it is. :(

im actually getting tired of it with the gloria. sometimes its worth it. but when washing the car when its warm or even partial sunlight, its a race against time. Drying/chamois has never been so f**king time consuming AND so important. and mine isnt even daily. dunno how people do it.

found out trying photograph black cars at night in average lighting, with average camera skills is hard.

What sort of coatings on it.. Dry with a good wet micro towel to get the bulk off, ( not a fan of chamois)then spray some quick detailer or something on the towel and go over it again.. Still time consuming but can be done in 10-15mins..

Not sure, I was happy with the whiskey. :D

Haha if you want another, I'll get you to go over Leesh's...it's got a lot of cobwebs and some light marring.

Actually need to get her rear bar re-glasses and gone over too.

No one wants to touch the fiberglass

Have a chicken tonight jar worth of paint though if you wanna glass and spray it

I did say we could fix it, somehow..

Probably because some numpty fused the bumper the body, it cant be taken off for repair.. But we can patch it up if you want..

Anyway I'm too busy lately to do much.. Haven't washed my own cars for yonks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...